Difficulty
Moderate
Steps
6
Time Required
15 - 20 minutes
Sections
1
- Water plug & water
- 6 steps
Flags
Member-Contributed Guide
An awesome member of our community made this guide. It is not managed by iFixit staff.
BackWater Dancing Speakers
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Water plug & water
- You will need to have a clean work space, water dancing speakers, super glue, mineral water, and Phillips screw driver ready.
- Unplug the USB cable powering your speakers before you continue.
You will need to have a clean work space, water dancing speakers, super glue, mineral water, and Phillips screw driver ready.
Unplug the USB cable powering your speakers before you continue.
1024
Step 2
- Using the phillips screw driver remove the 4 screws seen on the back of speakers.
Using the phillips screw driver remove the 4 screws seen on the back of speakers.
Step 3
- Once the four screws are taken out you will need to slide the bottom piece from the water canister.
- When the two are separated set the water canister bottom facing up.
Once the four screws are taken out you will need to slide the bottom piece from the water canister.
When the two are separated set the water canister bottom facing up.
Step 4
- On the bottom of the water canister you will see a hole where the water was inserted. There will be a black plug covering the hole.
- Using your screw driver you can pry the plug out.
- Once the plug is taken out you can refill the speakers. Only refill the speakers with one inch of water.
On the bottom of the water canister you will see a hole where the water was inserted. There will be a black plug covering the hole.
Using your screw driver you can pry the plug out.
Once the plug is taken out you can refill the speakers. Only refill the speakers with one inch of water.
Step 5
- After the water is filled to approximately one inch. Super glue the hole shut and let dry.
After the water is filled to approximately one inch. Super glue the hole shut and let dry.
Step 6
- When the glue is dry slide speaker back on to water canister.
- Once they are put together place back panel on and insert the four screws.
- repeat steps 2 through 6 on second speaker.
When the glue is dry slide speaker back on to water canister.
Once they are put together place back panel on and insert the four screws.
repeat steps 2 through 6 on second speaker.
Your water dancing speakers are now ready for use. Thank you for using this guide.
Cancel: I did not complete this guide.
46 other people completed this guide.
Author
with 5 other contributors
Andrew
Member since: 02/17/2015
1,304 Reputation
2 Guides authored
Badges:
11
+8 more badges
Team
Vegas Room H9
Member of Vegas Room H9
Community
13 Members
16 Guides authored
andrepicard2012 - Mar 3, 2016
Reply
the pump is defective how to replace
Lacepage - Mar 4, 2016
Reply
I couldnt get plug out either so I drilled a hole in back and filled it with mineral water and sealed it with a small strip of scotch tape and duct tape on top of that in case I had to get back in. It works, but now it looks different. Sometimes the water clings to the inside and it looks a little foggy. Is it mineral water, or mineral oil? If it leaks again I’ll prob try the oil.
aeromojito - Mar 29, 2016
Reply
The original liquid has a lower surface tension than water. I used odorless mineral spirits.
If the pump is noisy, try a drop of oil in the motor.
Andrew - Jul 24, 2016
Reply
My speakers keep spraying even though their is no music playing, is that a good thing?
Skittlekingthefirst - Nov 26, 2022
That means that the speakers are broken. You might need to replace it. If not, then its a probelm with the board, which I have no idea how to fix.
