Wacom Cintiq 24Hd Usb Accessory Port Replacement Repair Guide

Difficulty

Difficult

Steps

Time Required

                          30 minutes - 1 hour

Sections

Stand
3 steps
Back Panel
2 steps
USB Accessory Port
3 steps

Flags

BackWacom Cintiq 24HD
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications

Introduction

What you need

Step 1

              Stand

Unplug any cables from the USB, power, display or DVI-D ports by gripping the cord by the connector and pulling straight out of the port.
Unplugging the cables by pulling on the cord or pulling at an angle can damage the cable or connector.

Unplug any cables from the USB, power, display or DVI-D ports by gripping the cord by the connector and pulling straight out of the port.

Unplugging the cables by pulling on the cord or pulling at an angle can damage the cable or connector.

1024

Step 2

Place the device screen down on a flat surface.
Remove eight 10mm Phillips #2 screws (four on each leg of the stand) by turning the screwdriver counterclockwise.

Place the device screen down on a flat surface.

Remove eight 10mm Phillips #2 screws (four on each leg of the stand) by turning the screwdriver counterclockwise.

Step 3

Lift the stand up and away from the rest of the device so the legs separate from the mounting plate.

Lift the stand up and away from the rest of the device so the legs separate from the mounting plate.

Step 4

              Back Panel

Remove eighteen 10.2mm Phillips #1 screws from the perimeter of the back panel by turning the screwdriver counterclockwise.
Remove one 11.9mm Phillips #1 screw from the center of the back panel.
Remove two 10.2mm Phillips #1 screws from underneath hinged panels in the bottom right and left corners.
Our device does not include the cover panels for the USB, DVI-D, and power ports. You must first remove these cover panels shown in green in order to remove the back panel.

Remove eighteen 10.2mm Phillips #1 screws from the perimeter of the back panel by turning the screwdriver counterclockwise.

Remove one 11.9mm Phillips #1 screw from the center of the back panel.

Remove two 10.2mm Phillips #1 screws from underneath hinged panels in the bottom right and left corners.

Our device does not include the cover panels for the USB, DVI-D, and power ports. You must first remove these cover panels shown in green in order to remove the back panel.

Step 5

Lift the back panel up by a corner and insert a plastic opening tool in the gap.
Slide the tool along the gap around the perimeter of the device while lifting to unlatch the back panel.
The latches on the back panel will make loud clicking noises when opening.
Remove the panel by lifting it up and off of the device.

Lift the back panel up by a corner and insert a plastic opening tool in the gap.

Slide the tool along the gap around the perimeter of the device while lifting to unlatch the back panel.

The latches on the back panel will make loud clicking noises when opening.

Remove the panel by lifting it up and off of the device.

Step 6

              USB Accessory Port

Remove one 8mm Phillips #2 screw by turning the screwdriver counterclockwise
Remove one 9.9mm Phillips #2 screw by turning the screwdriver counterclockwise.

Remove one 8mm Phillips #2 screw by turning the screwdriver counterclockwise

Remove one 9.9mm Phillips #2 screw by turning the screwdriver counterclockwise.

Step 7

Remove the black grounding wire by lifting up.
Remove the USB port board by pinching the wiring close to the connector and gently pulling out.

Remove the black grounding wire by lifting up.

Remove the USB port board by pinching the wiring close to the connector and gently pulling out.

Step 8

Remove the USB port by melting the soldered connections with a soldering iron, then pulling the port off of the board.
iFixit has a guide to soldering which you can find here.

Remove the USB port by melting the soldered connections with a soldering iron, then pulling the port off of the board.

iFixit has a guide to soldering which you can find here.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      One other person completed this guide.

Author

                                      with 4 other contributors

                    Andrew Fleming

Member since: 10/08/2018

408 Reputation

                                      3 Guides authored                  



                       Badges:
                       8







                                                        +5 more badges

Team

                       Cal Poly, Team S15-G3, White Fall 2018                        

                                                  Member of Cal Poly, Team S15-G3, White Fall 2018 



                    CPSU-WHITE-F18S15G3                     


                                            4 Members                     


                                            9 Guides authored

Introduction#

What you need#

Team#

Introduction

What you need

Team