Wacker Compactor Plate Vp1550W 2007 V Belt Replacement Repair Guide

Difficulty

Easy

Steps

Time Required

                          10 minutes

Sections

V-Belt
7 steps

Flags

Grammar Police

Embrace your inner English teacher and help improve this guide’s grammar!

Bullets!

Better coordination with markups and the color/type of bullets will help make this guide more clear!

Member-Contributed Guide

An awesome member of our community made this guide. It is not managed by iFixit staff.

BackWacker Compactor Plate VP1550 - REV 110 (2007)
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications

Introduction

This guide is the same as “Wacker Plate Compactor VP1430AWAH 103 V-Belt Replacement,” as both machines are completely identical except for the size of the plate.

What you need

Step 1

              Locate the Belt Guard

The V-belt is located in a large gray compartment on the left side of the machine

The V-belt is located in a large gray compartment on the left side of the machine

1024

Step 2

              Locate and Loosen the Bolts

There are two 1/2 in bolts in the center of the belt guard cover that hold it on. Loosen them using the 1/2 in socket and the 3/8 in drive ratchet, but don’t fully remove them
Fully removing the bolts will cause a small O-ring to fall loose inside the belt guard

There are two 1/2 in bolts in the center of the belt guard cover that hold it on. Loosen them using the 1/2 in socket and the 3/8 in drive ratchet, but don’t fully remove them

Fully removing the bolts will cause a small O-ring to fall loose inside the belt guard

Step 3

              Inspect the Belt

Remove the belt guard cover and set it aside
Rotate the belt slowly, inspecting for signs of damage such as the crack shown

Remove the belt guard cover and set it aside

Rotate the belt slowly, inspecting for signs of damage such as the crack shown

Step 4

              Remove the Belt

Pull part of the V-belt up and over the top of the large pulley with one hand
Maintain tension on the belt while using your other hand to rotate the pulley clockwise until the belt comes off. This will require a bit of force
Remove the belt slowly and be careful not to get your fingers stuck between the belt and pulley
Clean any dirt or residue off of the area where the belt rode on the pulleys to ensure the new belt doesn’t get any unnecessary wear

Pull part of the V-belt up and over the top of the large pulley with one hand

Maintain tension on the belt while using your other hand to rotate the pulley clockwise until the belt comes off. This will require a bit of force

Remove the belt slowly and be careful not to get your fingers stuck between the belt and pulley

Clean any dirt or residue off of the area where the belt rode on the pulleys to ensure the new belt doesn’t get any unnecessary wear

Step 5

              Replace the New Belt

Loop the bottom of the belt around the small pulley
Pull the top of the belt around the bottom of the large pulley
Slowly twist the top pulley counter-clockwise while maintaining tension on the belt until the belt is completely on. This will require a bit of force
Be careful not to get your fingers caught between the belt and pulley as you rotate the new belt on

Loop the bottom of the belt around the small pulley

Pull the top of the belt around the bottom of the large pulley

Slowly twist the top pulley counter-clockwise while maintaining tension on the belt until the belt is completely on. This will require a bit of force

Be careful not to get your fingers caught between the belt and pulley as you rotate the new belt on

Step 6

              Clean the Belt Guard

Lightly pressure wash or otherwise clean the inside of the belt guard and belt guard cover. This will reduce wear and damage on the new belt

Lightly pressure wash or otherwise clean the inside of the belt guard and belt guard cover. This will reduce wear and damage on the new belt

Step 7

              Replace the Belt Guard

Line up the cover of the belt guard and place each bolt in its respective hole
Firmly press the belt guard cover into the rubber molding of the belt guard case to ensure proper sealing
Tighten the bolts firmly with a 1/2 in socket and a 3/8 in drive ratchet

Line up the cover of the belt guard and place each bolt in its respective hole

Firmly press the belt guard cover into the rubber molding of the belt guard case to ensure proper sealing

Tighten the bolts firmly with a 1/2 in socket and a 3/8 in drive ratchet

Cancel: I did not complete this guide.

                                                                                      3 other people completed this guide.

Author

                                      with 1 other contributor

                    ZACHARY

Member since: 10/17/2021

286 Reputation

                                      2 Guides authored                  



                       Badges:
                       4







                                                        +1 more badge

Team

                       The Home Depot                        

                                                  Member of The Home Depot 



                    Community                     


                                            10,914 Members                     


                                            33 Guides authored

Grammar Police#

Bullets!#

Member-Contributed Guide#

Introduction#

What you need#

Team#