Vtech Spin And Learn Color Flashlight Volume Selector Switch Replacement Repair Guide

Difficulty

Easy

Steps

6

Time Required

                          15 minutes            

Sections

5

• Battery Housing
• 1 step
• Speaker Housing
• 1 step
• Red Ring
• 2 steps
• Main Housing
• 1 step
• Volume Selector Switch
• 1 step

Flags

0

• BackVTech Spin and Learn Color Flashlight

• Full Screen

• Options

• History

• Save to Favorites

• Download PDF

• Edit

• Translate

• Get Shareable Link

• Embed This Guide

• Notify Me of Changes

• Stop Notifications

Introduction

What you need

Step 1

              Battery Housing               

• Locate the battery housing on the back of the flashlight as pictured.
• Unscrew the single 8 mm Phillips #1 screw.
• The screw will stay attached to the cover that will be removed.
• Lift the battery housing cover to reveal the battery terminals. Remove the batteries.

Locate the battery housing on the back of the flashlight as pictured.

Unscrew the single 8 mm Phillips #1 screw.

The screw will stay attached to the cover that will be removed.

Lift the battery housing cover to reveal the battery terminals. Remove the batteries.

1024

Step 2

              Speaker Housing               

• Locate the light blue speaker housing on the bottom of the flashlight.
• Remove the three 6 mm Phillips #0 screws.
• Once the screws have been removed, pull the housing away from the yellow body of the flashlight. Be careful not to disconnect the white wires from the speaker, unless speaker replacement is required.

Locate the light blue speaker housing on the bottom of the flashlight.

Remove the three 6 mm Phillips #0 screws.

Once the screws have been removed, pull the housing away from the yellow body of the flashlight. Be careful not to disconnect the white wires from the speaker, unless speaker replacement is required.

Step 3

              Red Ring               

• Locate the screw covering stickers on the side of the red ring. These two stickers will be slightly larger than the normal stickers. In this case it was a ladybug and a duck on opposite sides of the ring.
• With a plastic opening tool, gently remove the stickers by prying around the edges. Be careful with these as you will want to reapply them later

Locate the screw covering stickers on the side of the red ring. These two stickers will be slightly larger than the normal stickers. In this case it was a ladybug and a duck on opposite sides of the ring.

With a plastic opening tool, gently remove the stickers by prying around the edges. Be careful with these as you will want to reapply them later

Step 4

• Remove the two 8mm Phillips #0 screws from the screw channels found under the stickers in step one. This can be seen in the first photo if step 2.
• Once the screws have been successfully removed, grasp one half of the ring and pull gently to separate it from the yellow housing. Repeat on the opposite side and the ring is disassembled.

Remove the two 8mm Phillips #0 screws from the screw channels found under the stickers in step one. This can be seen in the first photo if step 2.

Once the screws have been successfully removed, grasp one half of the ring and pull gently to separate it from the yellow housing. Repeat on the opposite side and the ring is disassembled.

Step 5

              Main Housing               

• Unscrew the six 8 mm Phillips #0 screws at each of the points circled in red in the first image.
• To open, separate the two sides of the housing. They should come apart fairly easily, however you may use a spudger to pry it open. Once it’s apart, it should look like the second image.

Unscrew the six 8 mm Phillips #0 screws at each of the points circled in red in the first image.

To open, separate the two sides of the housing. They should come apart fairly easily, however you may use a spudger to pry it open. Once it’s apart, it should look like the second image.

Step 6

              Volume Selector Switch               

• Once the main housing is open, you will have to unscrew the 6 mm Phillips #0 screws from the motherboard to get to the volume selector.
• The Volume Selector is located in the back of the motherboard and sits in the slot as indicated in the 2nd image.

Once the main housing is open, you will have to unscrew the 6 mm Phillips #0 screws from the motherboard to get to the volume selector.

The Volume Selector is located in the back of the motherboard and sits in the slot as indicated in the 2nd image.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

Author

                                      with 3 other contributors 

                    Tess Puhak                     

Member since: 08/27/2015

347 Reputation

                                      3 Guides authored                  



                       Badges:
                       8







                                                        +5 more badges                           

Team

                       USF Tampa, Team 2-6, Blackwell Fall 2015                        

                                                  Member of USF Tampa, Team 2-6, Blackwell Fall 2015 



                    USFT-BLACKWELL-F15S2G6                     


                                            3 Members                     


                                            9 Guides authored