Difficulty
Difficult
Steps
9
Time Required
30 - 40 minutes
Sections
3
- Battery
- 2 steps
- Back Cover
- 2 steps
- LED
- 5 steps
Flags
0
BackVTech Little Apps Tablet
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Battery
- Remove the 9.9 mm screw covering the batteries with a PH1 driver head.
Remove the 9.9 mm screw covering the batteries with a PH1 driver head.
1024
Step 2
- Use a plastic opening tool to pry the batteries out of their holding.
- If replacing your batteries with new ones, be careful to insert them as indicated on the device.
Use a plastic opening tool to pry the batteries out of their holding.
If replacing your batteries with new ones, be careful to insert them as indicated on the device.
Step 3
Back Cover
- Position the VTech Little Apps Tablet face-down on a flat surface so that you can clearly see the back of the device.
- Remove all seven 9.6 mm screws located around the perimeter of the back cover with a PH1 driver head.
Position the VTech Little Apps Tablet face-down on a flat surface so that you can clearly see the back of the device.
Remove all seven 9.6 mm screws located around the perimeter of the back cover with a PH1 driver head.
Step 4
- Gently remove the back cover then flip it 180 degrees so that the back cover of the device is now face-down.
- Proceed with caution as there are wires attaching the back cover to the front cover of the device that could be easily detached.
Gently remove the back cover then flip it 180 degrees so that the back cover of the device is now face-down.
Proceed with caution as there are wires attaching the back cover to the front cover of the device that could be easily detached.
Step 5
LED
- Unscrew the two 7.3 mm screws using a PH0 driver head.
- Gently lift the beige circuit board and set aside.
- Be sure to not damage the wires connecting the circuit board to the motherboard, you are only creating space to work in.
Unscrew the two 7.3 mm screws using a PH0 driver head.
Gently lift the beige circuit board and set aside.
Be sure to not damage the wires connecting the circuit board to the motherboard, you are only creating space to work in.
Step 6
- Unscrew three 7.3 mm panhead screws with the PH0 driver.
- Remove the red-brown washer after removing the screws.
- Remove the black foam insert and set aside.
Unscrew three 7.3 mm panhead screws with the PH0 driver.
Remove the red-brown washer after removing the screws.
Remove the black foam insert and set aside.
Step 7
- Unscrew the 7.3 mm screw fastening the LED circuit board to the device shell with a PH0 driver head.
- Be careful when rescrewing circuit boards. Too much pressure or too tight of screws could damage them.
Unscrew the 7.3 mm screw fastening the LED circuit board to the device shell with a PH0 driver head.
Be careful when rescrewing circuit boards. Too much pressure or too tight of screws could damage them.
Step 8
- Gently lift both LED circuit board and the white glass light refractor panel away from the device.
- Separate the LED circuit board and light refractor panel by gently pulling apart. Place the light panel to the side.
- Skip the next step if you are proceeding with this guide as a part of the Screen Replacement.
Gently lift both LED circuit board and the white glass light refractor panel away from the device.
Separate the LED circuit board and light refractor panel by gently pulling apart. Place the light panel to the side.
Skip the next step if you are proceeding with this guide as a part of the Screen Replacement.
Step 9
- Carefully desolder the LED leads (labeled “R”, “+” and “B” on the circuit board) to disconnect the LED from the circuit board.
- Replace the LED and solder the new connection to the LED circuit board.
- Refer to the iFixit Soldering Guide for assistance.
Carefully desolder the LED leads (labeled “R”, “+” and “B” on the circuit board) to disconnect the LED from the circuit board.
Replace the LED and solder the new connection to the LED circuit board.
Refer to the iFixit Soldering Guide for assistance.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
Author
with 5 other contributors
Dakota Wiersma
Member since: 02/10/2016
223 Reputation
2 Guides authored
Badges:
10
+7 more badges
Team
USF Tampa, Team 2-6, Sullivan Spring 2016
Member of USF Tampa, Team 2-6, Sullivan Spring 2016
USFT-SULLIVAN-S16S2G6
3 Members
6 Guides authored