Difficulty
Easy
Steps
8
Time Required
20 minutes
Sections
2
- Display Assembly
- 7 steps
- Buttons
- 1 step
Flags
1
Featured Student Guide
This guide has been the hard work of our awesome students and is found to be exceptionally cool by the iFixit staff.
BackVTech Kidizoom Action Cam
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Display Assembly
- Make sure that the master power switch is set to the (O) position.
Make sure that the master power switch is set to the (O) position.
1024
Step 2
- Using a plastic opening tool, gently pry off the circular plating over the camera lens.
- The circular plating is held by a mild adhesive. It will not be necessary to replace this adhesive during the reassembly process.
Using a plastic opening tool, gently pry off the circular plating over the camera lens.
The circular plating is held by a mild adhesive. It will not be necessary to replace this adhesive during the reassembly process.
Step 3
- Use a #0 screwdriver to remove the two 2.5mm Phillips head screws located on the second layer of plating.
- Remove the second layer of plating previously held down by the screws by gripping it with your fingers and pulling upward.
- As there will be many screws being removed from the device, we recommend using a magnetic device such as the iFixit Magnetic Project Mat.
Use a #0 screwdriver to remove the two 2.5mm Phillips head screws located on the second layer of plating.
Remove the second layer of plating previously held down by the screws by gripping it with your fingers and pulling upward.
As there will be many screws being removed from the device, we recommend using a magnetic device such as the iFixit Magnetic Project Mat.
Step 4
- Pry off the transparent plating and paper design using a plastic opening tool.
Pry off the transparent plating and paper design using a plastic opening tool.
Step 5
- Unscrew the (4) 2.5mm Phillips head screws from the third layer of plating using a #0 screwdriver.
Unscrew the (4) 2.5mm Phillips head screws from the third layer of plating using a #0 screwdriver.
Step 6
- Turn the camera around and gently remove the plating that surrounds the LCD screen by grasping it with your fingers and pulling away from the device.
Turn the camera around and gently remove the plating that surrounds the LCD screen by grasping it with your fingers and pulling away from the device.
Step 7
- Use the plastic opening tool to lift the LCD screen, including the purple casing and set it aside, revealing the motherboard and connector ribbon.
- Exercise caution while performing this step, as any excessive pulling may tear the connector ribbon from the motherboard.
Use the plastic opening tool to lift the LCD screen, including the purple casing and set it aside, revealing the motherboard and connector ribbon.
Exercise caution while performing this step, as any excessive pulling may tear the connector ribbon from the motherboard.
Step 8
Buttons
- Push out the buttons that you wish to take out, and replace them with the new buttons.
- Cleaning the buttons may fix the issue of sticky buttons, and a replacement may not be necessary.
Push out the buttons that you wish to take out, and replace them with the new buttons.
Cleaning the buttons may fix the issue of sticky buttons, and a replacement may not be necessary.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
3 other people completed this guide.
Author
with 2 other contributors
Ross Anderson
Member since: 02/10/2016
606 Reputation
2 Guides authored
Badges:
12
+9 more badges
Team
USF Tampa, Team 3-5, Sullivan Spring 2016
Member of USF Tampa, Team 3-5, Sullivan Spring 2016
USFT-SULLIVAN-S16S3G5
3 Members
6 Guides authored
