Visual Land Prestige Elite 9Q Lcd Screen Replacement Repair Guide

Difficulty

Moderate

Steps

Time Required

Suggest a time??

Sections

LCD Screen
16 steps

Flags

Step Trimmer

This guide has unnecessary steps. Trim them to be more concise!

BackVisual Land Prestige Elite 9Q
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications

Introduction

What you need

Step 1

              LCD Screen

Using the large plastic opening tool, start along a side of the device and apply light pressure in the seam between the top and bottom outer covers.
Maneuver the smaller plastic opening tool at the spot of the large opening tool and slowly slide along the edge.
You should feel each plastic connections begin to loosen.

Using the large plastic opening tool, start along a side of the device and apply light pressure in the seam between the top and bottom outer covers.

Maneuver the smaller plastic opening tool at the spot of the large opening tool and slowly slide along the edge.

You should feel each plastic connections begin to loosen.

1024

Step 2

Move tool around each connection, and continue around the device until all connections have been loosened.
The user risks damaging the connections if they slide across to fast.

Move tool around each connection, and continue around the device until all connections have been loosened.

The user risks damaging the connections if they slide across to fast.

Step 3

Once all connections have been loosened and using a soft surface, place the device onto its screen and lift gently on the outer casing.
Open the casing and lay as shown keeping the speaker wires loose.
The highlighted areas represent connections to disassemble.

Once all connections have been loosened and using a soft surface, place the device onto its screen and lift gently on the outer casing.

Open the casing and lay as shown keeping the speaker wires loose.

The highlighted areas represent connections to disassemble.

Step 4

Using hook tweezers and a spudger, gently remove the glued speaker away from the casing.
The tweezers can damage the speaker.
The speaker is still connected to the motherboard with wire, so be cautious during this process.

Using hook tweezers and a spudger, gently remove the glued speaker away from the casing.

The tweezers can damage the speaker.

The speaker is still connected to the motherboard with wire, so be cautious during this process.

Step 5

Using wide-tip tweezers, gently remove the three pieces of tape attached to battery
The battery is still connected to the circuit board, and do not damage the tape as it holds the battery to the rest of the device.

Using wide-tip tweezers, gently remove the three pieces of tape attached to battery

The battery is still connected to the circuit board, and do not damage the tape as it holds the battery to the rest of the device.

Step 6

Next remove the WiFi module from the bottom of the device. This is simply pealed off.

Next remove the WiFi module from the bottom of the device. This is simply pealed off.

Step 7

Gently remove tape from circuit board, and disconnect the ZIF (zero insertion force) connectors for the front panel and LCD screen.
Use tweezers to lift up the black hinged lock on top of the ZIF connector.

Gently remove tape from circuit board, and disconnect the ZIF (zero insertion force) connectors for the front panel and LCD screen.

Use tweezers to lift up the black hinged lock on top of the ZIF connector.

Step 8

Use pointed hook tweezers to gently lift up front facing camera by grabbing the padding on back of camera.
Located on corner of tablet
Do not grab camera lens, tweezers may damage lens.

Use pointed hook tweezers to gently lift up front facing camera by grabbing the padding on back of camera.

Located on corner of tablet

Do not grab camera lens, tweezers may damage lens.

Step 9

Use pointed hook tweezers to gently remove rear facing camera by grabbing the corner of camera casing.
Located above charger jack.
Do not grab camera lens, tweezers will damage camera lens.

Use pointed hook tweezers to gently remove rear facing camera by grabbing the corner of camera casing.

Located above charger jack.

Do not grab camera lens, tweezers will damage camera lens.

Step 10

Use pointed hook tweezers to gently flip up hinged ZIF connector.
After ZIF connector is flipped up, remove camera module.

Use pointed hook tweezers to gently flip up hinged ZIF connector.

After ZIF connector is flipped up, remove camera module.

Step 11

These are the three screws holding the circuit board.
Use J00 or PH00 to remove the three screws.

These are the three screws holding the circuit board.

Use J00 or PH00 to remove the three screws.

Step 12

Make space in work area, and remove battery, circuit board, speaker, and wifi module as one from the LCD screen and front glass.
Handle carefully because battery speaker and wifi module are only connected by soldered connections.

Make space in work area, and remove battery, circuit board, speaker, and wifi module as one from the LCD screen and front glass.

Handle carefully because battery speaker and wifi module are only connected by soldered connections.

Step 13

Shown are all the clips that hold the LCD screen to the front glass.

Shown are all the clips that hold the LCD screen to the front glass.

Step 14

Start in the corner and pull back one of the black tabs. At the same time try to get under the screen with the tweezers.
Once one side is pulled up the rest should come off relatively easily.

Start in the corner and pull back one of the black tabs. At the same time try to get under the screen with the tweezers.

Once one side is pulled up the rest should come off relatively easily.

Step 15

After detaching front glass from LCD Screen, lay LCD screen down on white styrofoam side and this is what it will look like.
Do not place screen down on black side to prevent damaging screen

After detaching front glass from LCD Screen, lay LCD screen down on white styrofoam side and this is what it will look like.

Do not place screen down on black side to prevent damaging screen

Step 16

After removing LCD screen this is what the front glass component will look like.
At this point a better assessment can be made of whether the LCD screen is bad or the front glass is cracked.

After removing LCD screen this is what the front glass component will look like.

At this point a better assessment can be made of whether the LCD screen is bad or the front glass is cracked.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      2 other people completed this guide.

Author

                                      with 3 other contributors

                    Aaron

Member since: 07/19/2016

316 Reputation

                                      2 Guides authored                  



                       Badges:
                       8







                                                        +5 more badges

Team

                       University of Memphis, Team 1-1, Kim SU 2016                        

                                                  Member of University of Memphis, Team 1-1, Kim SU 2016 



                    UM-KIM-SU16S1G1                     


                                            4 Members                     


                                            8 Guides authored

Bill Shannon - Sep 15, 2017

Would this process work for the Prestige Elite 8qi as well?

Step Trimmer#

Introduction#

What you need#

Team#

Step Trimmer

Introduction

What you need

Team