Visual Land Prestige 7L Screen Replacement Repair Guide

Difficulty

Moderate

Steps

Time Required

                          30 minutes

Sections

Back Panel
3 steps
Screen
4 steps

Flags

BackVisual Land Prestige 7L
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications

Introduction

What you need

Step 1

              Back Panel

Remove the two 8mm Phillips Head screws located at the bottom of your device.

Remove the two 8mm Phillips Head screws located at the bottom of your device.

1024

Step 2

Insert the spudger between the two pieces of the case around the media ports and pry them apart.
We found the best way to get the spudger inside the case was to insert in into the SD card slot. Be sure to only insert the spudger a shallow amount and be careful not to damage any of the inside of the device.
Finish unsnapping each plastic piece holding the device together along the bottom.

Insert the spudger between the two pieces of the case around the media ports and pry them apart.

We found the best way to get the spudger inside the case was to insert in into the SD card slot. Be sure to only insert the spudger a shallow amount and be careful not to damage any of the inside of the device.

Finish unsnapping each plastic piece holding the device together along the bottom.

Step 3

Move the spudger down the rest of the case, separating each side, and finally the top.
Pull the back off and place it to the side.
Without a back panel for protection, be sure place your device on the table screen-side down to avoid damaging the internal circuitry.

Move the spudger down the rest of the case, separating each side, and finally the top.

Pull the back off and place it to the side.

Without a back panel for protection, be sure place your device on the table screen-side down to avoid damaging the internal circuitry.

Step 4

              Screen

Remove the tape holding the motherboard, wires, and connecters in place.

Remove the tape holding the motherboard, wires, and connecters in place.

Step 5

Unclip the three connectors by gently pulling the rear panel up and away from the motherboard.
For more information on unclipping connectors see this How To Guide
Pull out each of the gold connections.
The gold connections will disconnect from the motherboard, but not entirely from the device. Let them sit loosely where they are attached and be careful not to tear them when working in their proximity on the device.

Unclip the three connectors by gently pulling the rear panel up and away from the motherboard.

For more information on unclipping connectors see this How To Guide

Pull out each of the gold connections.

The gold connections will disconnect from the motherboard, but not entirely from the device. Let them sit loosely where they are attached and be careful not to tear them when working in their proximity on the device.

Step 6

Remove the seven 4mm Phillips Head screws that hold the touchscreen panel and motherboard together.

Remove the seven 4mm Phillips Head screws that hold the touchscreen panel and motherboard together.

Step 7

Gently flip over the motherboard and begin to use the spudger to pry away the touchscreen panel from the front screen.

Gently flip over the motherboard and begin to use the spudger to pry away the touchscreen panel from the front screen.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      3 other people completed this guide.

Author

                                      with 3 other contributors

                    Zach

Member since: 01/28/2015

486 Reputation

                                      2 Guides authored                  



                       Badges:
                       11







                                                        +8 more badges

Team

                       Penn State, Team 2-25, Kaschak Winter 2015                        

                                                  Member of Penn State, Team 2-25, Kaschak Winter 2015 



                    PSU-KASCHAK-W15S2G25                     


                                            4 Members                     


                                            4 Guides authored

GAZUTEC - Nov 27, 2017

Muchas gracias por tan importante aporte a la comunidad; desde Colombia con respeto. Atte. GAZUTEC

Introduction#

What you need#

Team#

Introduction

What you need

Team