Visual Land Prestige 10 Digitizer Replacement Repair Guide

Difficulty

Very difficult

Steps

Time Required

                          45 minutes - 1 hour

Sections

Back Case
4 steps
Battery
3 steps
Front Facing Camera
1 step
Motherboard
5 steps
LCD Display
1 step
Digitizer
2 steps

Flags

Better Introduction

Improve this guide by completing or revising its introduction.

BackVisual Land Prestige 10
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications

What you need

Step 1

              Back Case

Remove the 3mm screws from bottom of tablet with the precision screwdriver and place on magnetic mat. label where they came from.
All screws throughout this guide are the same 3mm size.

Remove the 3mm screws from bottom of tablet with the precision screwdriver and place on magnetic mat. label where they came from.

All screws throughout this guide are the same 3mm size.

1024

Step 2

Using the spudger, create a small opening to be used to open the back case.
While holding the case open, insert the plastic opening tool to get a larger opening.
Once you have a slight opening, insert the spudger and work around the edges, separating the back plate from the front.

Using the spudger, create a small opening to be used to open the back case.

While holding the case open, insert the plastic opening tool to get a larger opening.

Once you have a slight opening, insert the spudger and work around the edges, separating the back plate from the front.

Step 3

now that the case is open, carefully remove the speakers and set aside.

now that the case is open, carefully remove the speakers and set aside.

Step 4

Gently remove the speakers from the back case with tweezers and set the case aside.

Gently remove the speakers from the back case with tweezers and set the case aside.

Step 5

              Battery

Remove yellow tape from surrounding components.

Remove yellow tape from surrounding components.

Step 6

insert the spudger and gently work around and underneath the battery.
With the battery separated from the LCD Display, set it aside.
The battery is held down by very strong adhesive.

insert the spudger and gently work around and underneath the battery.

With the battery separated from the LCD Display, set it aside.

The battery is held down by very strong adhesive.

Step 7

Desolder and remove the 2 wires from the motherboard.
Use caution when desoldering to avoid damage to yourself or to the components.

Desolder and remove the 2 wires from the motherboard.

Use caution when desoldering to avoid damage to yourself or to the components.

Step 8

              Front Facing Camera

Locate the Camera Housing. Gently grip and lift the small black tab until you feel an audible click.
Gently remove the connector by pulling straight out, gripping the black connector head or as close as possible.
Gently grip and pull up the front camera, covered by protective adhesive foam.
Set aside the Camera housing.

Locate the Camera Housing. Gently grip and lift the small black tab until you feel an audible click.

Gently remove the connector by pulling straight out, gripping the black connector head or as close as possible.

Gently grip and pull up the front camera, covered by protective adhesive foam.

Set aside the Camera housing.

Step 9

              Motherboard

Locate the LCD Connector.
Using tweezers, grip the small black tab connected to the white plastic.
Gently lift the tab towards you until it clicks.
Remove the connector by pulling straight out, gripping the black connector head.

Locate the LCD Connector.

Using tweezers, grip the small black tab connected to the white plastic.

Gently lift the tab towards you until it clicks.

Remove the connector by pulling straight out, gripping the black connector head.

Step 10

Locate the Touchscreen connector and grip the forward-most black tab with the tweezers.
Lift the tab towards you until you feel an audible click.
Gently remove the connector by pulling straight out, gripping the black connector head.

Locate the Touchscreen connector and grip the forward-most black tab with the tweezers.

Lift the tab towards you until you feel an audible click.

Gently remove the connector by pulling straight out, gripping the black connector head.

Step 11

Gently lift up the WiFi antenna and set aside.

Gently lift up the WiFi antenna and set aside.

Step 12

Locate and remove the screws holding the volume and hold button controller. Set screws aside on magnetic mat and label them.
Gently lift up on the controller and leave it hanging loose.

Locate and remove the screws holding the volume and hold button controller. Set screws aside on magnetic mat and label them.

Gently lift up on the controller and leave it hanging loose.

Step 13

Remove screws located on motherboard.
Place on magnetic mat and label them
Gently remove the Motherboard and any wires connected to it and set it aside on a static free surface.

Remove screws located on motherboard.

Place on magnetic mat and label them

Gently remove the Motherboard and any wires connected to it and set it aside on a static free surface.

Step 14

              LCD Display

Remove the screws and plastic tabs holding the LCD Display and place them on the magnetic mat. Label them.
Gently remove the LCD Display and backlight by lifting up the LCD Connector with your fingers.
Set aside the LCD Assembly.
The LCD display and backlight are separated from one another. Be sure to remember how they are aligned when putting the device back together.

Remove the screws and plastic tabs holding the LCD Display and place them on the magnetic mat. Label them.

Gently remove the LCD Display and backlight by lifting up the LCD Connector with your fingers.

Set aside the LCD Assembly.

The LCD display and backlight are separated from one another. Be sure to remember how they are aligned when putting the device back together.

Step 15

              Digitizer

Simply lift up the loose metal frame and set aside.

Simply lift up the loose metal frame and set aside.

Step 16

Be extremely careful removing the touchscreen, avoiding sharp glass and hot surfaces.
Using the heating pad, heat the edges of the touchscreen to loosen the adhesive.
using the spudger, slowly and gently work around the edges, removing the touchscreen.
The Tablet we used came with a shattered screen, making this step much more difficult.

Be extremely careful removing the touchscreen, avoiding sharp glass and hot surfaces.

Using the heating pad, heat the edges of the touchscreen to loosen the adhesive.

using the spudger, slowly and gently work around the edges, removing the touchscreen.

The Tablet we used came with a shattered screen, making this step much more difficult.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      4 other people completed this guide.

Author

                                      with 1 other contributor

                    Connor Reese

Member since: 04/08/2015

1,244 Reputation

                                      6 Guides authored                  



                       Badges:
                       16







                                                        +13 more badges

Team

                       Eastern Washington University, Team 2-1, Matresse Spring 2015                        

                                                  Member of Eastern Washington University, Team 2-1, Matresse Spring 2015 



                    EWU-MATRESSE-S15S2G1                     


                                            3 Members                     


                                            12 Guides authored

Michael - Mar 24, 2017

Great write up, but have a question . Could you heat up the adhesive for the digitizer like an iPad and remove it without taking everything apart?

Better Introduction#

What you need#

Team#

Better Introduction

What you need

Team