Difficulty

Moderate

Steps

7

Time Required

Suggest a time??

Sections

1

  • Power Cord
  • 7 steps

Flags

0

  • BackMixer

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

What you need

Step 1

              Power Cord               
  • The tools you will need are:
  • Needle nose pliers
  • Tweezers
  • Slip joint pliers
  • A 9/32 &7/16 socket
  • Extension optional
  • A multi head screwdriver

The tools you will need are:

Needle nose pliers

Tweezers

Slip joint pliers

A 9/32 &7/16 socket

Extension optional

A multi head screwdriver

1024

Step 2

  • To begin you need to remove the top of the blender. To do this you must push inward on the tab located on the bottom of the top half of the machine. After pushing the tab you can then lift up using the handle to remove the top.

To begin you need to remove the top of the blender. To do this you must push inward on the tab located on the bottom of the top half of the machine. After pushing the tab you can then lift up using the handle to remove the top.

Step 3

  • Next you will need to tip the mixer onto its back to get a better angle. After you tip it onto its back, you will need to take a screwdriver with a 9/32 head or a 9/32 socket and unscrew the four bolts thus removing the black bottom tray.

Next you will need to tip the mixer onto its back to get a better angle. After you tip it onto its back, you will need to take a screwdriver with a 9/32 head or a 9/32 socket and unscrew the four bolts thus removing the black bottom tray.

Step 4

  • Here you will need your 7/16 socket and your slip joint pliers. First you will need fit your 7/16 socket on the hex nut on the bottom of the machine and your slip joint pliers on the rod sticking through the top of the machine. You will then loosen the nut with your socket while holding the top with your slip joint pliers.
  • By doing this you will be removing the flywheel thus giving you more room to remove the electrical connections.

Here you will need your 7/16 socket and your slip joint pliers. First you will need fit your 7/16 socket on the hex nut on the bottom of the machine and your slip joint pliers on the rod sticking through the top of the machine. You will then loosen the nut with your socket while holding the top with your slip joint pliers.

By doing this you will be removing the flywheel thus giving you more room to remove the electrical connections.

Step 5

  • At this step you will need your needle nose pliers to pry this angled tab straight which will allow you to pull it back through the slot.
  • After pulling the connector back through the slot a spring will begin to come out, do not remove or lose it.

At this step you will need your needle nose pliers to pry this angled tab straight which will allow you to pull it back through the slot.

After pulling the connector back through the slot a spring will begin to come out, do not remove or lose it.

Step 6

  • After you remove the first connection, this motor brush will begin to come out but do not remove it completely.

After you remove the first connection, this motor brush will begin to come out but do not remove it completely.

Step 7

  • Lastly you will need to use tweezers or needle nose pliers to remove the last electrical connection. With this connection all you need is to pull back on the metal part or the connection with your tweezers or needle nose pliers.

Lastly you will need to use tweezers or needle nose pliers to remove the last electrical connection. With this connection all you need is to pull back on the metal part or the connection with your tweezers or needle nose pliers.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      One other person completed this guide.                                             

Author

                                      with 3 other contributors 

                    Maxwell Schermerhorn                     

Member since: 05/31/2016

128 Reputation

                                      1 Guide authored                  



                       Badges:
                       3

Team

                       Central Coast New Tech High, Team 4-2, Rushing Spring 2016                        

                                                  Member of Central Coast New Tech High, Team 4-2, Rushing Spring 2016 



                    CCNTH-RUSHING-S16S4G2                     


                                            2 Members                     


                                            1 Guide authored