Difficulty
Easy
Steps
12
Time Required
5 - 10 minutes
Sections
3
- Plastic Case
- 5 steps
- Battery
- 4 steps
- Screen
- 3 steps
Flags
1
Needs Better Images
Better photos will improve this guide. Help out by taking, editing, or uploading new ones!
BackVerizon Ellipsis Jetpack MHS800L
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Plastic Case
- Remove the SIM card, that is located on top of the Jetpack.
Remove the SIM card, that is located on top of the Jetpack.
1024
Step 2
- With the device on its back and the label facing you, remove the rubber screw cover on the top left corner of the device.
- Under the rubber circle, remove the 1.25 mm screw using a Philips #00 screwdriver.
- You may need to peel back a piece of double sided tape covering the screw hole.
With the device on its back and the label facing you, remove the rubber screw cover on the top left corner of the device.
Under the rubber circle, remove the 1.25 mm screw using a Philips #00 screwdriver.
You may need to peel back a piece of double sided tape covering the screw hole.
Step 3
- Remove three 1.25 mm screws.
Remove three 1.25 mm screws.
Step 4
- Use a plastic opening tool at the seams and pry open the case.
Use a plastic opening tool at the seams and pry open the case.
Step 5
- Once the cover is off, this is what your device will look like.
Once the cover is off, this is what your device will look like.
Step 6
Battery
- Once you have the case off of your device gently pull your battery away from the device.
- Do not attempt to completely remove the battery, as it is still attached to the motherboard by wires.
Once you have the case off of your device gently pull your battery away from the device.
Do not attempt to completely remove the battery, as it is still attached to the motherboard by wires.
Step 7
- With a pair of ESD Tweezers remove the yellow tape covering the battery wires.
With a pair of ESD Tweezers remove the yellow tape covering the battery wires.
Step 8
- After removing the tape you may use the ESD Tweezers to remove the wiring harness from the circuit board.
- Do not squeeze the wires to hard you may damage them and cause a short.
After removing the tape you may use the ESD Tweezers to remove the wiring harness from the circuit board.
Do not squeeze the wires to hard you may damage them and cause a short.
Step 9
- You may now replace the battery in your Verizon Ellipsis Jetpack MHS800L.
You may now replace the battery in your Verizon Ellipsis Jetpack MHS800L.
Step 10
Screen
- Locate the LCD screen cable and unlatch the harness connection form the circuit board.
Locate the LCD screen cable and unlatch the harness connection form the circuit board.
Step 11
- Using the ESD Tweezers gently coax the display data cable out of circuit board connector.
- Do not squeeze the display data cable to hard you may damage it and cause a short.
Using the ESD Tweezers gently coax the display data cable out of circuit board connector.
Do not squeeze the display data cable to hard you may damage it and cause a short.
Step 12
- Gently insert the ESD Tweezers underneath the LCD screen and lift the LCD screen off of the circuit board.
Gently insert the ESD Tweezers underneath the LCD screen and lift the LCD screen off of the circuit board.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
One other person completed this guide.
Author
with 4 other contributors
Richard J Porras
Member since: 01/23/2016
504 Reputation
3 Guides authored
Badges:
11
+8 more badges
Team
IUPUI, Team 3-3, Baechle Spring 2016
Member of IUPUI, Team 3-3, Baechle Spring 2016
IUPUI-BAECHLE-S16S3G3
4 Members
6 Guides authored
