Difficulty
Difficult
Steps
11
Time Required
1 hour
Sections
1
- Power Button
- 11 steps
Flags
2
Needs Better Images
Better photos will improve this guide. Help out by taking, editing, or uploading new ones!
Needs More Images
A few more images would make this guide’s procedures crystal clear.
BackVerizon Ellipsis 7
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Power Button
- Power down device by holding down the power button until the screen goes black.
- Remove the SIM card from the device to prevent damage.
- To remove the SIM card, open the SIM card cover on the side of the device.
- Push SIM card in, then remove after it pops out with an audible click.
Power down device by holding down the power button until the screen goes black.
Remove the SIM card from the device to prevent damage.
To remove the SIM card, open the SIM card cover on the side of the device.
Push SIM card in, then remove after it pops out with an audible click.
1024
Step 2
- Take off the back panel.
- Pry open the back cover carefully with a plastic opening tool.
- Use the opening tool to disconnect the cover completely. Do not attempt to pull the back cover off with your hands.
- Be sure to pry open all sides of the device. Attempting to take off the back cover when part of it is attached may snap the cover.
Take off the back panel.
Pry open the back cover carefully with a plastic opening tool.
Use the opening tool to disconnect the cover completely. Do not attempt to pull the back cover off with your hands.
Be sure to pry open all sides of the device. Attempting to take off the back cover when part of it is attached may snap the cover.
Step 3
- Remove the charging (micro-USB) port by unscrewing the indicated screws using the Phillips #00 screwdriver.
- Disconnect the ribbon cable connecting the charging port board to the motherboard using tweezers.
- Use the tweezers to grab the sides of black, plastic connector. Do not grab from the wires or try to wedge it out from the bottom.
- Be extremely careful when disconnecting the ribbon cable. It is very delicate.
Remove the charging (micro-USB) port by unscrewing the indicated screws using the Phillips #00 screwdriver.
Disconnect the ribbon cable connecting the charging port board to the motherboard using tweezers.
Use the tweezers to grab the sides of black, plastic connector. Do not grab from the wires or try to wedge it out from the bottom.
Be extremely careful when disconnecting the ribbon cable. It is very delicate.
Step 4
- Disconnect speakers from motherboard.
- Use the tweezers to carefully disconnect speakers from motherboard.
Disconnect speakers from motherboard.
Use the tweezers to carefully disconnect speakers from motherboard.
Step 5
- Disconnect the battery.
- Use tweezers to carefully disengage connector.
Disconnect the battery.
Use tweezers to carefully disengage connector.
Step 6
- Disconnect the digitizer ribbon cable.
- Use a nylon spudger to lift back tab.
- After the back tab has been lifted the cable can be removed with tweezers.
- When using tweezers, be careful not to damage the ribbon cable.
Disconnect the digitizer ribbon cable.
Use a nylon spudger to lift back tab.
After the back tab has been lifted the cable can be removed with tweezers.
When using tweezers, be careful not to damage the ribbon cable.
Step 7
- Disconnect the ribbon cable.
- Use a nylon spudger to lift tab.
- After the tab is lifted, the cable can be removed.
Disconnect the ribbon cable.
Use a nylon spudger to lift tab.
After the tab is lifted, the cable can be removed.
Step 8
- Disconnect all antenna cables.
- Use a nylon spudger to pop the antenna cable from the base.
Disconnect all antenna cables.
Use a nylon spudger to pop the antenna cable from the base.
Step 9
- Remove 9 Phillips #00 screws. The length of 4.76 mm
- There is 1 Phillips #00 screw that is 3.175mm in length. This screw also has a larger head then the rest of the screws.
- Note: when reassembling the motherboard, screw the bigger headed screw in the original location.
Remove 9 Phillips #00 screws. The length of 4.76 mm
There is 1 Phillips #00 screw that is 3.175mm in length. This screw also has a larger head then the rest of the screws.
Note: when reassembling the motherboard, screw the bigger headed screw in the original location.
Step 10
- Remove the motherboard.
- Locate power button.
Remove the motherboard.
Locate power button.
Step 11
- Desolder the power button from the motherboard.
- Learn how to solder and desolder components here!
Desolder the power button from the motherboard.
Learn how to solder and desolder components here!
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
2 other people completed this guide.
Author
with 6 other contributors
Taylor Nieman
Member since: 10/10/2016
275 Reputation
1 Guide authored
Badges:
8
+5 more badges
Team
Sam Houston State, Team 12-7, Blackburne Fall 2016
Member of Sam Houston State, Team 12-7, Blackburne Fall 2016
SHSU-BLACKBURNE-F16S12G7
3 Members
10 Guides authored
tklahn79 - Jul 31, 2018
Reply
I dropped mine and the button is broke. It looks like I should be able to just pop it back, but it’s not reaching the button in the tablet. Do I really have to order this just for it to turn on? I mean, I use a paper clip, but I use this for Uber and it’s not safe when I’m driving, lol.
Regina Cain - Oct 17, 2019
Reply
I have looked everywhere for replacement buttons. Any help you can give in finding the parts is appreciated.