Difficulty
Moderate
Steps
13
Time Required
10 minutes
Sections
3
- Battery
- 3 steps
- Camera
- 5 steps
- External Speaker
- 5 steps
Flags
0
BackUTStarcom XV6700
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Battery
- Press the on/off button on the top to power the phone off.
Press the on/off button on the top to power the phone off.
1024
Step 2
- Remove the battery cover by pressing and sliding the cover down and off of the phone.
Remove the battery cover by pressing and sliding the cover down and off of the phone.
Step 3
- Pull the battery removal tab and lift the battery out of the phone.
- If the battery removal tab is missing, place a spudger on the opposite side of the highlighted connector and pry the battery up.
Pull the battery removal tab and lift the battery out of the phone.
If the battery removal tab is missing, place a spudger on the opposite side of the highlighted connector and pry the battery up.
Step 4
Camera
- Remove the two 4.0-mm #000 Phillips screws at the top of the battery compartment. Tweezers may be useful to remove the screws.
Remove the two 4.0-mm #000 Phillips screws at the top of the battery compartment. Tweezers may be useful to remove the screws.
Step 5
- Use firm pressure to carefully pry off the cover with your fingers.
Use firm pressure to carefully pry off the cover with your fingers.
Step 6
- Remove the 4.0-mm #00 Phillips screw securing the camera flash circuit board. The board is still connected by a connector on the bottom of the board.
Remove the 4.0-mm #00 Phillips screw securing the camera flash circuit board. The board is still connected by a connector on the bottom of the board.
Step 7
- Gently pry off the camera flash circuit board with the spudger.
Gently pry off the camera flash circuit board with the spudger.
Step 8
- Gently pry off the camera with the spudger.
Gently pry off the camera with the spudger.
Step 9
External Speaker
- Remove the four 5.0-mm Torx T6 screws from the corners of the black cover.
Remove the four 5.0-mm Torx T6 screws from the corners of the black cover.
Step 10
- Remove the 4.0-mm #00 Phillips screw that holds the wireless antenna in place. The antenna does not need to be removed.
Remove the 4.0-mm #00 Phillips screw that holds the wireless antenna in place. The antenna does not need to be removed.
Step 11
- Use the spudger and plastic opening tools to apply firm but gentle pressure equally around the outside of the case.
- Carefully pry the black portion of the case away from the silver portion.
- Do not try to remove case completely. The speaker wire is still connected to the motherboard.
Use the spudger and plastic opening tools to apply firm but gentle pressure equally around the outside of the case.
Carefully pry the black portion of the case away from the silver portion.
Do not try to remove case completely. The speaker wire is still connected to the motherboard.
Step 12
- Using tweezers, pull on the connector or wire in the direction of the wire with gentle pressure to unplug the wire connector from the motherboard.
Using tweezers, pull on the connector or wire in the direction of the wire with gentle pressure to unplug the wire connector from the motherboard.
Step 13
- Press your finger on the speaker from the outside of the housing, and the speaker will come out.
Press your finger on the speaker from the outside of the housing, and the speaker will come out.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
Author
with 2 other contributors
Tyson Janisch
Member since: 06/04/2013
317 Reputation
3 Guides authored
Badges:
9
+6 more badges
Team
University of Kentucky Louisville, Team 1-4, Chamberlain Spring 2013
Member of University of Kentucky Louisville, Team 1-4, Chamberlain Spring 2013
LOUISVILLE-CHAMBERLAIN-S13S1G4
3 Members
8 Guides authored
