Difficulty
Difficult
Steps
6
Time Required
1 hour
Sections
1
- USB Cable Repair
- 6 steps
Flags
Action Shots
Be an action hero! This guide needs images that better demonstrate how to perform specific actions.
BackEngage Wired Optical Mouse
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
USB Cable Repair
- Remove the broken portion of the USB cable with the wire cutters.
- You should now have two pieces of the cable left. If you had to remove the whole USB plug, you’ll need a replacement plug.
Remove the broken portion of the USB cable with the wire cutters.
You should now have two pieces of the cable left. If you had to remove the whole USB plug, you’ll need a replacement plug.
1024
Step 2
- Cut the outer cable covering with wire cutters or scissors of both cables and be careful not to cut the wires themselves.
- Pull off the piece of cover that you’ve separated from the rest. You should be left with four exposed individual wires.
- There should be four wires, and occasionally a piece of string too. If there are fewer wires, then you’ve clipped one off, and you need to start over.
- If there are more than 4 wires, you probably have a USB 3.0 cable. In this case, make sure that whatever wires you’ll be reconnecting are both USB 3.0.
Cut the outer cable covering with wire cutters or scissors of both cables and be careful not to cut the wires themselves.
Pull off the piece of cover that you’ve separated from the rest. You should be left with four exposed individual wires.
There should be four wires, and occasionally a piece of string too. If there are fewer wires, then you’ve clipped one off, and you need to start over.
If there are more than 4 wires, you probably have a USB 3.0 cable. In this case, make sure that whatever wires you’ll be reconnecting are both USB 3.0.
Step 3
- Strip all the wires out from both cables using a wire stripper. You’ll need about three quarters of an inch of exposed copper wire.
- If you don’t have a wire stripper, you can strip the wires the same way as you exposed these wires. Gently cut the outer insulation, then pull off the insulation.
- When stripping wires, do not cut or damage the copper wires. If you do damage the wire, cut off the damaged portion and try again.
Strip all the wires out from both cables using a wire stripper. You’ll need about three quarters of an inch of exposed copper wire.
If you don’t have a wire stripper, you can strip the wires the same way as you exposed these wires. Gently cut the outer insulation, then pull off the insulation.
When stripping wires, do not cut or damage the copper wires. If you do damage the wire, cut off the damaged portion and try again.
Step 4
- Solder like-colored wires to each other.
- Here is a video on how to solder wires together. https://www.youtube.com/watch?v=qxqZJH3S…
Solder like-colored wires to each other.
Here is a video on how to solder wires together. https://www.youtube.com/watch?v=qxqZJH3S…
Step 5
- Wrap each wire in electrical tape and make sure that there is no exposed copper showing.
Wrap each wire in electrical tape and make sure that there is no exposed copper showing.
Step 6
- Wrap all the wires and both cables together in electrical tape to connect everything back into one cable and so it lasts longer.
Wrap all the wires and both cables together in electrical tape to connect everything back into one cable and so it lasts longer.
Once your device is assembled and taped up then the repair is done and you can go back and do this multiple times.
Cancel: I did not complete this guide.
25 other people completed this guide.
Author
with 8 other contributors
David
Member since: 01/16/2013
1,019 Reputation
4 Guides authored
Badges:
13
+10 more badges
Team
Cal Poly, Team 18-36, Regan Winter 2013
Member of Cal Poly, Team 18-36, Regan Winter 2013
CPSU-REGAN-W13S18G36
3 Members
26 Guides authored
obito uchiha - Mar 10, 2016
Reply
thanks you verb much
very i meant
Bethany Marshall - Mar 13, 2017
Reply
What if it has a wire shield around it? Like crazy silver wires wrapped around it?
kotanwolf - Mar 30, 2017
Then slowly wnwrap it not to remove it. And when u have repaired wires and taped them re wrap with silver shielding if it does have shielding it best to add a step to the repair and tbats to add a short section of shrink tubeing just big enough to cover spliced section and shielding. Once shielding is wrapped slid tubeing over repaired section and apply heat a hairdryer on high heat will work as well.
Faizan Ali - Oct 25, 2018
Reply
i tried solding the same wires but it still do not work