Usb Auxiliary Port Repair Guide

Difficulty

Moderate

Steps

Time Required

                          20 - 30 minutes

Sections

Outer Case
5 steps
USB/Auxiliary Port
12 steps

Flags

Step Trimmer

This guide has unnecessary steps. Trim them to be more concise!

Better Introduction

Improve this guide by completing or revising its introduction.

BackJawbone MINI JAMBOX
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications

What you need

Step 1

              Outer Case

Using the standard metal spudger, begin by prying at the bottom of the plain rubber end cap (the end without the USB or auxiliary input).

Using the standard metal spudger, begin by prying at the bottom of the plain rubber end cap (the end without the USB or auxiliary input).

1024

Step 2

Continue prying around the end panel, prying at different points until the entire panel is out of its seating.
Carefully remove the end panel.
The tabs which connect the panel are on the short sides.
WARNING: you will likely cause cosmetic damage to the end cap.

Continue prying around the end panel, prying at different points until the entire panel is out of its seating.

Carefully remove the end panel.

The tabs which connect the panel are on the short sides.

WARNING: you will likely cause cosmetic damage to the end cap.

Step 3

Slide out the rubber foot located on the bottom of the case.

Slide out the rubber foot located on the bottom of the case.

Step 4

Using a T6 bit, remove the flat topped 5mm screw located on the bottom of the casing, underneath the rubber foot.
This is the only flat topped screw in the speaker, so keep track of which one it is.

Using a T6 bit, remove the flat topped 5mm screw located on the bottom of the casing, underneath the rubber foot.

This is the only flat topped screw in the speaker, so keep track of which one it is.

Step 5

Push against the side without end cap to slide the internal components out of the case.
While holding the metal outset casing with one hand, press on the black inner plastic casing with your thumb.
It will be very difficult the first time. There is a rubber seal on the outside of the plastic inner case that creates a lot of friction with the metal outer case.

Push against the side without end cap to slide the internal components out of the case.

While holding the metal outset casing with one hand, press on the black inner plastic casing with your thumb.

It will be very difficult the first time. There is a rubber seal on the outside of the plastic inner case that creates a lot of friction with the metal outer case.

Step 6

              USB/Auxiliary Port

Using the standard metal spudger, carefully pry up the top 2 plastic tabs which hold the exterior button and port cover onto the interior plastic frame.

Using the standard metal spudger, carefully pry up the top 2 plastic tabs which hold the exterior button and port cover onto the interior plastic frame.

Step 7

Using the classic metal spudger, pry up the bottom 2 tabs attaching the other side of the button panel.
It should come off after prying up the first tab.

Using the classic metal spudger, pry up the bottom 2 tabs attaching the other side of the button panel.

It should come off after prying up the first tab.

Step 8

Carefully lift out the end panel.
Unplug both the connection ribbon and the ZIF ribbon using tweezers or your hands.
There is a bit of glue to hold the connection ribbon down.

Carefully lift out the end panel.

Unplug both the connection ribbon and the ZIF ribbon using tweezers or your hands.

There is a bit of glue to hold the connection ribbon down.

Step 9

Remove the 5mm T6 screw holding the port assembly onto the end cap.
Unlike the flat top screw holding the metal housing, these screws are roundtop.

Remove the 5mm T6 screw holding the port assembly onto the end cap.

Unlike the flat top screw holding the metal housing, these screws are roundtop.

Step 10

Remove the old port assembly from the end cap.
Alternate Reassembly required, read on.

Remove the old port assembly from the end cap.

Alternate Reassembly required, read on.

Step 11

Disconnect the Motherboard connection ribbon from the motherboard.
The ribbon should no longer be connected at either end.

Disconnect the Motherboard connection ribbon from the motherboard.

The ribbon should no longer be connected at either end.

Step 12

Very carefully pull the motherboard connection ribbon through the plastic casing, removing it from the plastic casing.

Very carefully pull the motherboard connection ribbon through the plastic casing, removing it from the plastic casing.

Step 13

Insert the connection ribbon into its ZIF connection port on the bottom of the new port assembly
ZIF connectors are delicate and often give beginners trouble, search for ZIF connector tips on the web.

Insert the connection ribbon into its ZIF connection port on the bottom of the new port assembly

ZIF connectors are delicate and often give beginners trouble, search for ZIF connector tips on the web.

Step 14

Position the new port assembly on the end cap and reinsert the 5mm T6 screw.
The rubber insulation around the motherboard connector should help hold the ZIF connector in place after the screw has been reinserted.

Position the new port assembly on the end cap and reinsert the 5mm T6 screw.

The rubber insulation around the motherboard connector should help hold the ZIF connector in place after the screw has been reinserted.

Step 15

Reconnect the button ribbon connector on the top of the port assembly.

Reconnect the button ribbon connector on the top of the port assembly.

Step 16

Reconnect the endcap to the plastic housing.
While you reconnect the endcap to the plastic housing, carefully position the ribbon slide through the ribbon slit and into the plastic casing.

Reconnect the endcap to the plastic housing.

While you reconnect the endcap to the plastic housing, carefully position the ribbon slide through the ribbon slit and into the plastic casing.

Step 17

Snap the end cap back onto the inner plastic casing and reconnect the ZIF ribbon to the motherboard.
Finish reassembling in descending order starting at step 5.

Snap the end cap back onto the inner plastic casing and reconnect the ZIF ribbon to the motherboard.

Finish reassembling in descending order starting at step 5.

To reassemble your device, follow steps 1 through 5 in reverse order.

Cancel: I did not complete this guide.

                                                                                      5 other people completed this guide.

Author

                                      with 4 other contributors

                    Noah Sadler

Member since: 04/01/2015

548 Reputation

                                      2 Guides authored                  



                       Badges:
                       15







                                                        +12 more badges

Team

                       Cal Poly, Team 12-1, Lancaster Spring 2015                        

                                                  Member of Cal Poly, Team 12-1, Lancaster Spring 2015 



                    CPSU-LANCASTER-S15S12G1                     


                                            5 Members                     


                                            10 Guides authored

barrysum - Jan 5, 2016

Can anyone at all tell us where we can definitely purchase the USB/Auxiliary Port and its Motherboard to Aux Port ZIF Ribbon?

Thanks in advance.

Step Trimmer#

Better Introduction#

What you need#

Team#

Step Trimmer

Better Introduction

What you need

Team