Difficulty

Moderate

Steps

7

Time Required

                          5 - 10 minutes

Sections

4

  • Battery Cover
  • 1 step
  • Battery Pack
  • 1 step
  • Back Shell
  • 3 steps
  • Circuit Board
  • 2 steps

Flags

1

Needs Better Images

Better photos will improve this guide. Help out by taking, editing, or uploading new ones!

  • BackUniden TCX905

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

What you need

Step 1

              Battery Cover
  • Starting from the top of the cover, slide down and away from the phone with your thumb
  • Lift battery cover off of batter and place it to the side

Starting from the top of the cover, slide down and away from the phone with your thumb

Lift battery cover off of batter and place it to the side

1024

Step 2

              Battery Pack
  • Once battery cover is removed, place your thumb and index fingers on the the wires near the receptacle
  • Gently pull straight up on the wires until a click is heard which signifies the battery is completely disconnected
  • Place battery pack to the side

Once battery cover is removed, place your thumb and index fingers on the the wires near the receptacle

Gently pull straight up on the wires until a click is heard which signifies the battery is completely disconnected

Place battery pack to the side

Step 3

              Back Shell
  • Remove the two 11mm screws inside the battery storage compartment using Phillips #1 screwdriver (located near the very bottom of the phone)

Remove the two 11mm screws inside the battery storage compartment using Phillips #1 screwdriver (located near the very bottom of the phone)

Step 4

  • Gently open phone casing along the seam at the bottom of the phone using index and middle fingers of both hands

Gently open phone casing along the seam at the bottom of the phone using index and middle fingers of both hands

Step 5

  • Ensure that wired connection between circuit board and back shell is not strained
  • Fold the back shell underneath the front shell and circuit board

Ensure that wired connection between circuit board and back shell is not strained

Fold the back shell underneath the front shell and circuit board

Step 6

              Circuit Board
  • Carefully remove the middle two 7mm screws, the outer top 9mm screws, and the top middle 7 mm screw that hold the logic board to the front shell of the phone casing using the Phillips #1 screwdriver

Carefully remove the middle two 7mm screws, the outer top 9mm screws, and the top middle 7 mm screw that hold the logic board to the front shell of the phone casing using the Phillips #1 screwdriver

Step 7

  • Using index finger and thumb, carefully remove the circuit board from the front shell of phone

Using index finger and thumb, carefully remove the circuit board from the front shell of phone

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

Author

                                      with 3 other contributors 


                    Gary Pence

Member since: 03/26/2014

807 Reputation

                                      8 Guides authored                  



                       Badges:
                       8







                                                        +5 more badges

Team

                       Clemson, Team 1-1, Benson Spring 2014                        

                                                  Member of Clemson, Team 1-1, Benson Spring 2014 



                    CLEM-BENSON-S14S1G1                     


                                            3 Members                     


                                            16 Guides authored

zrubene - Apr 3, 2017

Reply

I liveI at Buenos Aires, Argentina. I need to repaire a Uniden TCX905 Circuit Board and I wish to receive the manual for repaire, if it existe. Thanks in advance . Ruben E. (zrubene@gmail.com)