Uniden D1685 Front Panel And Keypad Replacement Repair Guide

Difficulty

Moderate

Steps

12

Time Required

                          5 - 10 minutes            

Sections

1

• Front Panel and Keypad
• 12 steps

Flags

Better Introduction

Improve this guide by completing or revising its introduction.

• BackUniden D1685-3T

• Full Screen

• Options

• History

• Save to Favorites

• Download PDF

• Edit

• Translate

• Get Shareable Link

• Embed This Guide

• Notify Me of Changes

• Stop Notifications

Introduction

What you need

Step 1

              Front Panel and Keypad               

• Turn the phone over with the back facing upwards.

Turn the phone over with the back facing upwards.

1024

Step 2

• Press your thumb down on the top of the cover and push downwards.

Press your thumb down on the top of the cover and push downwards.

Step 3

• Once removed the battery will be connected by 2 wires.
• Do not pull the red and black wires.

Once removed the battery will be connected by 2 wires.

Do not pull the red and black wires.

Step 4

• Pull the small, grey connector that is connected to the phone to disconnect the battery pack.

Pull the small, grey connector that is connected to the phone to disconnect the battery pack.

Step 5

• Remove the two 3.175 mm screws with the small Phillips head (PH1) screwdriver on the bottom of the phone next to where the battery was removed.

Remove the two 3.175 mm screws with the small Phillips head (PH1) screwdriver on the bottom of the phone next to where the battery was removed.

Step 6

• Once removed, use plastic opening tool to pull the back and front apart in 3 different locations; the bottom and both sides.

Once removed, use plastic opening tool to pull the back and front apart in 3 different locations; the bottom and both sides.

Step 7

• After splitting the phone there will be 2 wires that connect the phone’s circuit board with the speaker on the back.
• Do not pull the red and black wires.

After splitting the phone there will be 2 wires that connect the phone’s circuit board with the speaker on the back.

Step 8

• The circuit board (Large Green) is attached by 1 3.175mm screw in the top, left corner.
• Remove this screw using a small Phillips head screwdriver (PH!) from the iFixit toolkit.

The circuit board (Large Green) is attached by 1 3.175mm screw in the top, left corner.

Remove this screw using a small Phillips head screwdriver (PH!) from the iFixit toolkit.

Step 9

• Once the screw has been removed, the circuit board will be removable.
• Gently remove the circuit board and place it on the back of the phone.

Once the screw has been removed, the circuit board will be removable.

Gently remove the circuit board and place it on the back of the phone.

Step 10

• The keyboard will now be accessible. Remove the Bumper Pad (rubber pad behind actual keypad).
• Remove the keypad.

The keyboard will now be accessible. Remove the Bumper Pad (rubber pad behind actual keypad).

Remove the keypad.

Step 11

• Clean the pad with cleaning spray and/or a brush.

Clean the pad with cleaning spray and/or a brush.

Step 12

• Once cleaned, make sure to dry off all of the components entirely.

Once cleaned, make sure to dry off all of the components entirely.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      One other person completed this guide.                                             

Author

                                      with 8 other contributors 

                    William Mullens                     

Member since: 03/27/2015

215 Reputation

                                      2 Guides authored                  



                       Badges:
                       5







                                                        +2 more badges                           

Team

                       University of Alabama, Team 1-4, Naidoo Spring 2015                        

                                                  Member of University of Alabama, Team 1-4, Naidoo Spring 2015 



                    UA-NAIDOO-S15S1G4                     


                                            5 Members                     


                                            6 Guides authored                     

Honda Dude - Nov 6, 2018

Reply

Did all of the above but I can’t get the center piece to work! I have no volume control and I can’t access anything like phone numbers, etc.