Difficulty

Moderate

Steps

9

Time Required

                          30 minutes

Sections

2

  • Back Panel
  • 5 steps
  • Speaker
  • 4 steps

Flags

3

Needs Better Images

Better photos will improve this guide. Help out by taking, editing, or uploading new ones!

In Progress

This guide is a work in progress. Reload periodically to see the latest changes!

Needs More Images

A few more images would make this guide’s procedures crystal clear.

  • BackUnbranded UB-15MS10

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

What you need

Step 1

              Back Panel
  • Remove the cover over the Micro SD outlet by using a plastic opening tool to pry open and push out the cover panel.

Remove the cover over the Micro SD outlet by using a plastic opening tool to pry open and push out the cover panel.

1024

Step 2

  • Remove the two 4-mm #0 screws from the inside of the Micro SD compartment.

Remove the two 4-mm #0 screws from the inside of the Micro SD compartment.

Step 3

  • Insert blue guitar picks in the crease between the top and bottom panels starting on the same end as the Micro SD slot.
  • Inserting the picks directly under the Micro SD compartment was the easiest place to get started. It still requires some force.

Insert blue guitar picks in the crease between the top and bottom panels starting on the same end as the Micro SD slot.

Inserting the picks directly under the Micro SD compartment was the easiest place to get started. It still requires some force.

Step 4

  • Insert the black spudger between the guitar picks in order to pry open gaps between the blue guitar picks.
  • As the gaps open, slide the guitar picks along the sides to separate the panels.

Insert the black spudger between the guitar picks in order to pry open gaps between the blue guitar picks.

As the gaps open, slide the guitar picks along the sides to separate the panels.

Step 5

  • Pry all four sides apart using the blue guitar picks and the black spudger until they can easily be pried apart by hand.

Pry all four sides apart using the blue guitar picks and the black spudger until they can easily be pried apart by hand.

Step 6

              Speaker
  • Remove the yellow tape from the speaker.

Remove the yellow tape from the speaker.

Step 7

  • Remove the two 4-mm #0 screws holding the speaker in place.
  • The copper-colored plastic piece covering the speaker does not need to be removed from the device, move it to the side to reach the screws.

Remove the two 4-mm #0 screws holding the speaker in place.

The copper-colored plastic piece covering the speaker does not need to be removed from the device, move it to the side to reach the screws.

Step 8

  • Remove the silver tape covering the speaker’s black and red wires.

Remove the silver tape covering the speaker’s black and red wires.

Step 9

  • Reflow the solder of the black and red wires from the circuit board by using the soldering iron.
  • For more information about using a soldering iron click here.

Reflow the solder of the black and red wires from the circuit board by using the soldering iron.

For more information about using a soldering iron click here.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

Author

                                      with 7 other contributors 


                    Jordan Turk

Member since: 09/21/2015

331 Reputation

                                      2 Guides authored                  



                       Badges:
                       10







                                                        +7 more badges

Team

                       IUPUI, Team 2-1, Baechle Fall 2015                        

                                                  Member of IUPUI, Team 2-1, Baechle Fall 2015 



                    IUPUI-BAECHLE-F15S2G1                     


                                            3 Members                     


                                            3 Guides authored