Difficulty
Moderate
Steps
8
Time Required
30 minutes
Sections
2
- Ear Cushions
- 3 steps
- Right Speaker
- 5 steps
Flags
0
BackTurtle Beach Elite Pro
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Ear Cushions
- Firmly pinch ear cushion between thumb and forefinger.
- Using the hand not holding the ear cushion, grasp the orange plate that is below the ear cushion.
- If the black rubber lining on the orange plate is grasped, then the rubber lining on the ear piece may tear.
Firmly pinch ear cushion between thumb and forefinger.
Using the hand not holding the ear cushion, grasp the orange plate that is below the ear cushion.
If the black rubber lining on the orange plate is grasped, then the rubber lining on the ear piece may tear.
1024
Step 2
- Rotate ear cushion counter-clockwise about half an inch.
- The ear cushion should audibly snap out of place.
- After it has audibly snapped out of place, lift the ear cushion off of the device.
- During reassembly, rotate the ear cushion clockwise.
Rotate ear cushion counter-clockwise about half an inch.
The ear cushion should audibly snap out of place.
After it has audibly snapped out of place, lift the ear cushion off of the device.
During reassembly, rotate the ear cushion clockwise.
Step 3
- Using the new cushion, align the pegs located on both the orange plate and ear cushion.
- Make sure that both the ear cushion and the orange plate have the same designation.
- Once the pegs are aligned, push the new ear cushion in place.
Using the new cushion, align the pegs located on both the orange plate and ear cushion.
Make sure that both the ear cushion and the orange plate have the same designation.
Once the pegs are aligned, push the new ear cushion in place.
Step 4
Right Speaker
- Remove the right ear cushion.
- The right ear piece does not have any additional attachments.
Remove the right ear cushion.
The right ear piece does not have any additional attachments.
Step 5
- Using the Phillips #0 screwdriver, remove the 6.0 mm screws on the orange plate.
Using the Phillips #0 screwdriver, remove the 6.0 mm screws on the orange plate.
Step 6
- Use the opening tool to separate the orange plate from the black base plate.
- Focus on the wires that are connected to the speaker.
Use the opening tool to separate the orange plate from the black base plate.
Focus on the wires that are connected to the speaker.
Step 7
- Cut the two wires that are attached to the speaker.
- Cut the wires as close to the speaker as possible. These wires will be used in the next step.
Cut the two wires that are attached to the speaker.
Cut the wires as close to the speaker as possible. These wires will be used in the next step.
Step 8
- Replace the old speaker with the new speaker.
- Using the soldering iron, solder the wires to the new speaker.
- Make sure to solder the wires to their original locations on the speaker.
Replace the old speaker with the new speaker.
Using the soldering iron, solder the wires to the new speaker.
Make sure to solder the wires to their original locations on the speaker.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
One other person completed this guide.
Author
with 3 other contributors
Alexis Uribe
Member since: 03/24/2017
510 Reputation
4 Guides authored
Badges:
14
+11 more badges
Team
Baylor, Team S5-G1, Williams Spring 2017
Member of Baylor, Team S5-G1, Williams Spring 2017
BU-WILLIAMS-S17S5G1
3 Members
8 Guides authored
