Turntable Needle Replacement And Calibration Repair Guide

Difficulty

Moderate

Steps

7

Time Required

                          10 minutes            

Sections

1

• Needle
• 7 steps

Flags

0

• BackAudio-Technica AT-LP120XUSB-SV

• Full Screen

• Options

• History

• Save to Favorites

• Download PDF

• Edit

• Translate

• Get Shareable Link

• Embed This Guide

• Notify Me of Changes

• Stop Notifications

Introduction

If your turntable needle is bent, this can worsen the sound quality of the vinyl record, and damage the actual vinyl record itself, and can damage the needle used to play the vinyl record . When the turntable needle calibration is disrupted, this can damage the needle itself.

Before using this guide, inspect the turntable needle to ensure that there is not debris that is interfering with the turntable needle. If there is any dust that is collected on the needle, this can be removed simply by using your fingers, or by using a small vinyl record brush.

Before beginning this guide, make sure to remove any vinyl records that are on the turntable, and make sure that the power is off.

What you need

Step 1

              Needle               

• Begin with an Audio-Technica AT-LP120XUSB-SV Manual Turntable, with the tonearm placed in the tonearm holder off to the side.
• Twist the metal ring at the end of stylus (needle) cartridge counterclockwise.
• After the metal ring is twisted, there should be a space between metal ring and stylus cartridge.

Begin with an Audio-Technica AT-LP120XUSB-SV Manual Turntable, with the tonearm placed in the tonearm holder off to the side.

Twist the metal ring at the end of stylus (needle) cartridge counterclockwise.

After the metal ring is twisted, there should be a space between metal ring and stylus cartridge.

1024

Step 2

• Pull the stylus cartridge away from the tonearm.
• Flip the cartridge on its back, so the underside is exposed.

Pull the stylus cartridge away from the tonearm.

Flip the cartridge on its back, so the underside is exposed.

Step 3

• Pull the green stylus holder away from the cartridge.
• If the stylus is bent, you can either bend it in place to straighten it, or you can replace the stylus.

Pull the green stylus holder away from the cartridge.

If the stylus is bent, you can either bend it in place to straighten it, or you can replace the stylus.

Step 4

• Once the stylus has either been straightened or replaced, place the green cover back onto the cartridge and push down until it “clicks” in place.

Once the stylus has either been straightened or replaced, place the green cover back onto the cartridge and push down until it “clicks” in place.

Step 5

• Download the Audio Technica Cartridge/Headshell Adjustment Protractor.
• Print the protractor, and place it on the turntable.
• Make sure that the metal rod in the center of the turntable is placed where the hole is located on the protractor

Download the Audio Technica Cartridge/Headshell Adjustment Protractor.

Print the protractor, and place it on the turntable.

Make sure that the metal rod in the center of the turntable is placed where the hole is located on the protractor

Step 6

• Place the stylus on the dot in the center of the “A lines”, furthest away from the center of the record.
• Check to see if the edge of stylus cartridge is aligned with the “B lines” on the protractor.
• When the edge of the stylus cartridge is not aligned with the “B lines” on the protractor, this means it is out of alignment and needs to be calibrated. To begin, make sure that the tonearm is in the lifted position, by lifting the tonearm lever.

Place the stylus on the dot in the center of the “A lines”, furthest away from the center of the record.

Check to see if the edge of stylus cartridge is aligned with the “B lines” on the protractor.

When the edge of the stylus cartridge is not aligned with the “B lines” on the protractor, this means it is out of alignment and needs to be calibrated. To begin, make sure that the tonearm is in the lifted position, by lifting the tonearm lever.

Step 7

• Hold the cartridge in place, and use the screwdriver to unscrew the screws on top of the cartridge.
• Once the cartridge is loose, slide the screws and check alignment to see if the stylus box lines up with the “B lines”.
• Once the cartridge lines up with the “B lines”, use the screwdriver to secure the screws in place.

Hold the cartridge in place, and use the screwdriver to unscrew the screws on top of the cartridge.

Once the cartridge is loose, slide the screws and check alignment to see if the stylus box lines up with the “B lines”.

Once the cartridge lines up with the “B lines”, use the screwdriver to secure the screws in place.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

Author

                                      with 1 other contributor 

                    Leah Lloyd                     

Member since: 04/25/2020

146 Reputation

                                      1 Guide authored                  



                       Badges:
                       3

Team

                       UW Tacoma, Team S1-G12, Cardinal Spring 2020                        

                                                  Member of UW Tacoma, Team S1-G12, Cardinal Spring 2020 



                    UWT-CARDINAL-S20S1G12                     


                                            2 Members                     


                                            1 Guide authored