Difficulty
Easy
Steps
7
Time Required
10 minutes
Sections
1
- Replacing a Tribute Kendama String
- 7 steps
Flags
0
BackToy
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Video Overview
Step 1
Replacing a Tribute Kendama String
- Remove the damaged string and the small plastic bead completely, using scissors if necessary.
- If knots have come undone, but the string is intact, follow the knot tying instructions under step 5.
Remove the damaged string and the small plastic bead completely, using scissors if necessary.
If knots have come undone, but the string is intact, follow the knot tying instructions under step 5.
1024
Step 2
- Place the body of the kendama face down.
- The big cup should be on the right-hand side.
Place the body of the kendama face down.
The big cup should be on the right-hand side.
Step 3
- Begin by inserting one end of the new string straight through the hole at the crosspiece.
- The official minimum kendama string length is 38 cm or about 15 inches. Longer strings provide players with more of a challenge.
Begin by inserting one end of the new string straight through the hole at the crosspiece.
The official minimum kendama string length is 38 cm or about 15 inches. Longer strings provide players with more of a challenge.
Step 4
- Flip the kendama over to the other side, so that the big cup is now on the left-hand side.
- Pull the end of the string until it extends about an inch out of the hole. This will be used to tie the knot.
Flip the kendama over to the other side, so that the big cup is now on the left-hand side.
Pull the end of the string until it extends about an inch out of the hole. This will be used to tie the knot.
Step 5
- To tie the knot, begin by taking the inch of extended string and making a small loop.
- Put the tip of the string through the loop.
- Put the tip of the string through the loop a second time to strengthen the knot. Pull the knot tight.
To tie the knot, begin by taking the inch of extended string and making a small loop.
Put the tip of the string through the loop.
Put the tip of the string through the loop a second time to strengthen the knot. Pull the knot tight.
Step 6
- Now, we will attach the ball.
- Begin by placing the ball upright, with the small hole on top.
- Insert the free end of the string through the small hole, and continue pushing it through until it comes out the big hole on the bottom.
- Wetting the string or dipping it in glue will make the string straighter and easier to thread through the ball.
Now, we will attach the ball.
Begin by placing the ball upright, with the small hole on top.
Insert the free end of the string through the small hole, and continue pushing it through until it comes out the big hole on the bottom.
Wetting the string or dipping it in glue will make the string straighter and easier to thread through the ball.
Step 7
- Thread the free end of the string through a small plastic bead, and allow the bead to slide down into the ball.
- Now, with about an inch of string extending out from the big hole, we will tie a knot on the free end of the string, just like what was done in step 5.
- Adjust the two knots to reach your preferred string length.
- The kendama is ready to go!
Thread the free end of the string through a small plastic bead, and allow the bead to slide down into the ball.
Now, with about an inch of string extending out from the big hole, we will tie a knot on the free end of the string, just like what was done in step 5.
Adjust the two knots to reach your preferred string length.
The kendama is ready to go!
Strings are bound to become damaged through excessive kendama use. However, these steps should save you plenty of time and frustration when repairing your beloved kendama.
For replacement strings visit: https://shop.kendamausa.com/collections/…
Cancel: I did not complete this guide.
Author
with 3 other contributors
Andrew Melrose
Member since: 04/09/2015
101 Reputation
1 Guide authored
Badges:
2
Team
Cal Poly, Team 28-3, Green Spring 2015
Member of Cal Poly, Team 28-3, Green Spring 2015
CPSU-GREEN-S15S28G3
4 Members
7 Guides authored
Brite Cloud - Jul 2, 2022
Reply
This tutorial is awesome, waiting for the next tutorial on how to be 99 parsing warlock.