Difficulty

Moderate

Steps

10

Time Required

                          20 minutes

Sections

1

  • Traxxas Stampede Remote Control Truck 12T Brushed Motor Disassembly
  • 10 steps

Flags

2

Action Shots

Be an action hero! This guide needs images that better demonstrate how to perform specific actions.

Needs More Images

A few more images would make this guide’s procedures crystal clear.

  • BackToy

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

What you need

Step 1

              Traxxas Stampede Remote Control Truck 12T Brushed Motor Disassembly
  • Remove the fastner clips on all four corners of the body.

Remove the fastner clips on all four corners of the body.

1024

Step 2

  • Lifting straight up, remove the plastic body from the truck, exposing the inner components.

Lifting straight up, remove the plastic body from the truck, exposing the inner components.

Step 3

  • Using a Phillips #1 screwdriver, on the rear right side, remove the center screw from the green wheelie bar.

Using a Phillips #1 screwdriver, on the rear right side, remove the center screw from the green wheelie bar.

Step 4

  • Using the Phillips #1 screwdriver, remove the center screw on the left side of the green wheelie bar.

Using the Phillips #1 screwdriver, remove the center screw on the left side of the green wheelie bar.

Step 5

  • Pull the black power wire in an outward motion on both sides of the clear plastic sleeve to disconnect the motor from the battery. Repeat this with the red power wire to disconnect it from the battery.

Pull the black power wire in an outward motion on both sides of the clear plastic sleeve to disconnect the motor from the battery. Repeat this with the red power wire to disconnect it from the battery.

Step 6

  • Remove the right rear wheel, using a 7.0 mm socket-or R.C. wheel wrench to loosen the Nyloc nut.
  • Pull the wheel straight out removing it from the truck.

Remove the right rear wheel, using a 7.0 mm socket-or R.C. wheel wrench to loosen the Nyloc nut.

Pull the wheel straight out removing it from the truck.

Step 7

  • Using a number Phillips #1 screwdriver, remove the two screws that hold the plastic motor housing together.
  • Pull the motor housing straight out and remove.

Using a number Phillips #1 screwdriver, remove the two screws that hold the plastic motor housing together.

Pull the motor housing straight out and remove.

Step 8

  • Using a 1/16 Allen wrench, loosen the set screw inside the small gear that holds the motor in place.
  • Pull straight out to remove the gear from the motor shaft.

Using a 1/16 Allen wrench, loosen the set screw inside the small gear that holds the motor in place.

Pull straight out to remove the gear from the motor shaft.

Step 9

  • Remove two Phillips #1 head screws holding the motor in place.

Remove two Phillips #1 head screws holding the motor in place.

Step 10

  • Grasping the motor, slide it out towards the left tire, removing it entirely.
  • Now you have removed the old motor and can replace it with a new one.

Grasping the motor, slide it out towards the left tire, removing it entirely.

Now you have removed the old motor and can replace it with a new one.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

Author

                                      with 1 other contributor 


                    Ashley

Member since: 10/08/2019

181 Reputation

                                      1 Guide authored                  



                       Badges:
                       2

Team

                       Eastern Washington University, Team S27-G3, Munoz Fall 2019                        

                                                  Member of Eastern Washington University, Team S27-G3, Munoz Fall 2019 



                    EWU-MUNOZ-F19S27G3                     


                                            1 Member                     


                                            1 Guide authored