Toshiba Satellite U405D S2902 Faceplate Replacement Repair Guide

Difficulty

Moderate

Steps

Time Required

                          30 minutes

Sections

Battery
2 steps
Keyboard
4 steps
Faceplate
12 steps

Flags

Needs Better Images

Better photos will improve this guide. Help out by taking, editing, or uploading new ones!

Needs More Images

A few more images would make this guide’s procedures crystal clear.

BackToshiba Satellite U405D-S2902
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications

Introduction

What you need

Step 1

              Battery

Make sure that the laptop is off and unplugged.
Turn the laptop over.
Slide back the left lock, and you should hear a click when it is successfully locked back in.

Make sure that the laptop is off and unplugged.

Turn the laptop over.

Slide back the left lock, and you should hear a click when it is successfully locked back in.

1024

Step 2

Rotate the laptop 180 degrees so that the battery is near you.
Hold back the spring slide and pull the battery out.

Rotate the laptop 180 degrees so that the battery is near you.

Hold back the spring slide and pull the battery out.

Step 3

              Keyboard

Situate the laptop so that it is open and the display is facing you.
Use the plastic opening tool to pry the black plastic insert upward. The insert can be found at the top of the keyboard.
Once the insert is loose, carefully remove it from the device.

Situate the laptop so that it is open and the display is facing you.

Use the plastic opening tool to pry the black plastic insert upward. The insert can be found at the top of the keyboard.

Once the insert is loose, carefully remove it from the device.

Step 4

Using #1 Phillips Screwdriver, remove both of the 5 mm screws that are located beneath the insert.

Using #1 Phillips Screwdriver, remove both of the 5 mm screws that are located beneath the insert.

Step 5

Use the plastic opening tool to begin removing the keys off of the device.
Once the keys are off, gently remove the keyboard. Be careful of the ribbon cable that still connects the keyboard to motherboard.

Use the plastic opening tool to begin removing the keys off of the device.

Once the keys are off, gently remove the keyboard. Be careful of the ribbon cable that still connects the keyboard to motherboard.

Step 6

Lift up the gate on the ZIF socket to release the ribbon.
Ease the ribbon connecting the keyboard to the motherboard out of the ZIF socket.

Lift up the gate on the ZIF socket to release the ribbon.

Ease the ribbon connecting the keyboard to the motherboard out of the ZIF socket.

Step 7

              Faceplate

With the keyboard removed, locate the marked screws.
Remove the marked, 5mm screws using the #1 Phillips Screwdriver.

With the keyboard removed, locate the marked screws.

Remove the marked, 5mm screws using the #1 Phillips Screwdriver.

Step 8

In the opening above the mouse pad, use the plastic opening tool to push up the black gate of the ZIF socket.
Remove the ribbon from the ZIF socket.

In the opening above the mouse pad, use the plastic opening tool to push up the black gate of the ZIF socket.

Remove the ribbon from the ZIF socket.

Step 9

Locate the wide opening at the top near the screen.
Use the plastic opening tool to open the black ZIF socket.
Remove the blue ribbon.

Locate the wide opening at the top near the screen.

Use the plastic opening tool to open the black ZIF socket.

Remove the blue ribbon.

Step 10

After removing the screw in step 3, carefully close the laptop and put it face down. Locate the center panel.
Remove the three, 3 mm screws using the #1 Phillips Screwdriver.

After removing the screw in step 3, carefully close the laptop and put it face down. Locate the center panel.

Remove the three, 3 mm screws using the #1 Phillips Screwdriver.

Step 11

Grasp the power cable with your tweezers and remove it from the wireless antenna.

Grasp the power cable with your tweezers and remove it from the wireless antenna.

Step 12

Locate and remove both the white and black antenna leads with the tweezers.

Locate and remove both the white and black antenna leads with the tweezers.

Step 13

Remove screws for back assembly.
11 x F5 (5 mm #1 Phillips)
6 x F2 (2 mm #0 Phillips)
4 x F8 (8 mm #1 Phillips)
1 x F3 (3 mm #1 Phillips

Remove screws for back assembly.

11 x F5 (5 mm #1 Phillips)

6 x F2 (2 mm #0 Phillips)

4 x F8 (8 mm #1 Phillips)

1 x F3 (3 mm #1 Phillips

Step 14

Use the plastic opening tool to release the back panel from the laptop.
If all of the screws are removed it should come off with very little effort. Do not force it. If it still feels attached, check that you didn’t miss a screw or two.

Use the plastic opening tool to release the back panel from the laptop.

If all of the screws are removed it should come off with very little effort. Do not force it. If it still feels attached, check that you didn’t miss a screw or two.

Step 15

Use the plastic opening tool to separate the top faceplate.
The faceplate is the plastic surface and the metal piece under the keyboard.
Carefully lift the faceplate off of the base by sliding the plastic opening tool around the outside of the device. You’ll hear clicks as you do this.
Prying apart the faceplate will be a little hard, but try not to bend it too much - you do not want to crack it.

Use the plastic opening tool to separate the top faceplate.

The faceplate is the plastic surface and the metal piece under the keyboard.

Carefully lift the faceplate off of the base by sliding the plastic opening tool around the outside of the device. You’ll hear clicks as you do this.

Prying apart the faceplate will be a little hard, but try not to bend it too much - you do not want to crack it.

Step 16

Lift the back panel and carefully disconnect the main power cable.

Lift the back panel and carefully disconnect the main power cable.

Step 17

Remove the black signal cable attached at the blue circuit board.

Remove the black signal cable attached at the blue circuit board.

Step 18

Remove auxiliary power cable attached to the blue board at the back of the laptop.

Remove auxiliary power cable attached to the blue board at the back of the laptop.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      One other person completed this guide.

Author

                                      with 8 other contributors

                    Brandon Kirklen

Member since: 01/11/2013

311 Reputation

                                      8 Guides authored                  



                       Badges:
                       12







                                                        +9 more badges

Team

                       Cal Poly, Team 7-8, Maness Winter 2013                        

                                                  Member of Cal Poly, Team 7-8, Maness Winter 2013 



                    CPSU-MANESS-W13S7G8                     


                                            4 Members                     


                                            8 Guides authored

Needs Better Images#

Needs More Images#

Introduction#

What you need#

Team#

Needs Better Images

Needs More Images

Introduction

What you need

Team