Difficulty
Moderate
Steps
21
Time Required
20 - 45 minutes
Sections
1
- Motherboard
- 21 steps
Flags
0
BackToshiba Satellite Radius P55W-B5220
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Motherboard
- Using the plastic opening tool, remove the two rubber feet closest to the hinge.
Using the plastic opening tool, remove the two rubber feet closest to the hinge.
1024
Step 2
- Remove the 12 M2x4mm PH0 Philips screws.
Remove the 12 M2x4mm PH0 Philips screws.
Step 3
- Near the hinges, wedge a plastic opening tool under the back panel.
Near the hinges, wedge a plastic opening tool under the back panel.
Step 4
- Unlatch the LED indicator from the back panel.
Unlatch the LED indicator from the back panel.
Step 5
- Using a P0 Philips head screwdriver, Remove the four M2x2.5mm P0 Philips screws from the battery.
Using a P0 Philips head screwdriver, Remove the four M2x2.5mm P0 Philips screws from the battery.
Step 6
- Lift the battery.
- Disconnect the battery.
Lift the battery.
Disconnect the battery.
Step 7
- Disconnect the ribbon cable of the touchpad from the motherboard.
Disconnect the ribbon cable of the touchpad from the motherboard.
Step 8
- Remove the two M2x2.5mm P0 Philips screws from the fan.
Remove the two M2x2.5mm P0 Philips screws from the fan.
Step 9
- Disconnect the fan cables.
- Carefully unhook the wires from the base of the fan.
Disconnect the fan cables.
Carefully unhook the wires from the base of the fan.
Step 10
- Unscrew the four M2x4mm PH0 Philips screws from the CPU mounts on the motherboard.
Unscrew the four M2x4mm PH0 Philips screws from the CPU mounts on the motherboard.
Step 11
- Carefully lift the heatsink off the CPU.
- Avoid bending or kinking the tubing.
- Delicately lift the fan out with the heatsink.
Carefully lift the heatsink off the CPU.
Avoid bending or kinking the tubing.
Delicately lift the fan out with the heatsink.
Step 12
- Remove the M2x2.5mm P0 Philips screw from the USB controller.
Remove the M2x2.5mm P0 Philips screw from the USB controller.
Step 13
- Lift the USB controller from the motherboard.
- Detach the USB controller from the motherboard.
Lift the USB controller from the motherboard.
Detach the USB controller from the motherboard.
Step 14
- Disconnect the left speaker from the motherboard.
Disconnect the left speaker from the motherboard.
Step 15
- Remove the two M2x4mm PH0 Philips screws for the speaker mounts.
Remove the two M2x4mm PH0 Philips screws for the speaker mounts.
Step 16
- Unhook the speaker from under the hinge cable mounts.
Unhook the speaker from under the hinge cable mounts.
Step 17
- Unhook the right speaker cable from the motherboard.
Unhook the right speaker cable from the motherboard.
Step 18
- Remove the copper tape from the speaker cord.
Remove the copper tape from the speaker cord.
Step 19
- Unhook the speaker cables from under the catch under the hinge.
Unhook the speaker cables from under the catch under the hinge.
Step 20
- Remove the eight M2x2.5mm P0 Philips screws from the motherboard.
Remove the eight M2x2.5mm P0 Philips screws from the motherboard.
Step 21
- Remove the motherboard.
Remove the motherboard.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
2 other people completed this guide.
Author
with 1 other contributor
Nicole Kohm
Member since: 09/20/2017
131 Reputation
1 Guide authored
Badges:
6
+3 more badges
Team
University of North Texas, Team S5-G6, Thomas Fall 2017
Member of University of North Texas, Team S5-G6, Thomas Fall 2017
UNT-THOMAS-F17S5G6
5 Members
6 Guides authored
