Toshiba Satellite Radius P55W B5112 Ram Replacement Repair Guide

Difficulty

Easy

Steps

Time Required

                          10 - 20 minutes

Sections

Battery Replacement
6 steps
RAM Replacement
2 steps

Flags

BackToshiba Satellite Radius P55W-B5112
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications

Introduction

What you need

Step 1

              Battery Replacement

Unplug your laptop from any source of power.
Lay your laptop on a soft, clean surface as shown.
Using the metal spudger, remove the two rubber grips on the bottom face of the laptop, located closest to the hinge.
The grips may be brittle. Be careful when removing them with the metal spudger so as not to damage them.

Unplug your laptop from any source of power.

Lay your laptop on a soft, clean surface as shown.

Using the metal spudger, remove the two rubber grips on the bottom face of the laptop, located closest to the hinge.

The grips may be brittle. Be careful when removing them with the metal spudger so as not to damage them.

1024

Step 2

Remove the ten 5mm Phillips #0 screws that secure the back plate to the computer.

Remove the ten 5mm Phillips #0 screws that secure the back plate to the computer.

Step 3

Starting on the edge that is opposite the hinge, use the plastic opening tools to pry the back plate away from the computer.
Loosen the three non-hinge edges.
Leave a plastic opening tool in each corner to ensure that one side does not snap closed before you are done opening the others.
DO NOT lift the back plate away from the computer; it is still connected to the motherboard.

Starting on the edge that is opposite the hinge, use the plastic opening tools to pry the back plate away from the computer.

Loosen the three non-hinge edges.

Leave a plastic opening tool in each corner to ensure that one side does not snap closed before you are done opening the others.

DO NOT lift the back plate away from the computer; it is still connected to the motherboard.

Step 4

To loosen the back plate, lift it slightly and gently pull it away from the hinge.
Flip the back plate open towards the power button, but be sure to not pull on the ribbon cable that connects the back plate to the motherboard.
Use a plastic opening tool to detach the side of the ribbon cable connected to the computer by prying up gently on the small black lever at the point of attachment.

To loosen the back plate, lift it slightly and gently pull it away from the hinge.

Flip the back plate open towards the power button, but be sure to not pull on the ribbon cable that connects the back plate to the motherboard.

Use a plastic opening tool to detach the side of the ribbon cable connected to the computer by prying up gently on the small black lever at the point of attachment.

Step 5

Remove the four 3mm Phillips #0 screws connecting the battery to the computer.

Remove the four 3mm Phillips #0 screws connecting the battery to the computer.

Step 6

Use a plastic opening tool to lift the side of the battery that is closest to the long edge of the computer.
As you are pulling the battery away from the computer, unplug it from the side closest to the short edge of the computer.
There may be a lot of resistance when unplugging the battery. If there is, try to wiggle the male side of the plug back and forth as you remove it.

Use a plastic opening tool to lift the side of the battery that is closest to the long edge of the computer.

As you are pulling the battery away from the computer, unplug it from the side closest to the short edge of the computer.

There may be a lot of resistance when unplugging the battery. If there is, try to wiggle the male side of the plug back and forth as you remove it.

Step 7

              RAM Replacement

Use a spudger to gently pry up the plastic brackets holding on each RAM drive. The long edges of each drive furthest from one another should pop up at an angle.
While a metal spudger is used in these photos, using plastic opening tools instead will lower your chances of damaging your device.

Use a spudger to gently pry up the plastic brackets holding on each RAM drive. The long edges of each drive furthest from one another should pop up at an angle.

While a metal spudger is used in these photos, using plastic opening tools instead will lower your chances of damaging your device.

Step 8

Remove each RAM drive by pulling at an upwards angle in the direction of its free edge.

Remove each RAM drive by pulling at an upwards angle in the direction of its free edge.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      3 other people completed this guide.

Author

                                      with 4 other contributors

                    Mudassar Abbas Khan

Member since: 10/19/2017

624 Reputation

                                      5 Guides authored                  



                       Badges:
                       9







                                                        +6 more badges

Team

                       UMass Dartmouth, Team S66-G5, Rockett Fall 2017                        

                                                  Member of UMass Dartmouth, Team S66-G5, Rockett Fall 2017 



                    UMASSD-ROCKETT-F17S66G5                     


                                            3 Members                     


                                            5 Guides authored

victor vela - May 8, 2019

Hola estimado, quiera saber el código de la pieza conector hdd sata para Toshiba satellite P55W-B5112

Alton Franklin - Jun 25, 2019

Ya done great, bro!!!! Kudos and many thanks!!!

Introduction#

What you need#

Team#

Introduction

What you need

Team