Difficulty
Moderate
Steps
12
Time Required
1 hour
Sections
1
- Screen
- 12 steps
Flags
Action Shots
Be an action hero! This guide needs images that better demonstrate how to perform specific actions.
BackToshiba Satellite p875 s7200
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Screen
- Remove the battery by sliding the tabs to the left.
- Use the spudger to lift out the battery.
Remove the battery by sliding the tabs to the left.
Use the spudger to lift out the battery.
1024
Step 2
- Use the Phillips head screw driver to remove the screw holding the back plate on.
Use the Phillips head screw driver to remove the screw holding the back plate on.
Step 3
- Remove the 6 mm screws around the edges with the Phillips head screw driver. Then remove the 6mm screw holding the disc drive into place.
- Sliding out the disc drive will reveal the final two 4 mm screws on the bottom of the device.
Remove the 6 mm screws around the edges with the Phillips head screw driver. Then remove the 6mm screw holding the disc drive into place.
Sliding out the disc drive will reveal the final two 4 mm screws on the bottom of the device.
Step 4
- Flip the laptop over to begin the process of removing the keyboard.
- Use the spudger to pop the keyboard off. Start at the bottom of the keyboard and work your way around.
Flip the laptop over to begin the process of removing the keyboard.
Use the spudger to pop the keyboard off. Start at the bottom of the keyboard and work your way around.
Step 5
- Use the Phillips head screw driver to remove the last 6mm screws holding the case together.
- The screws are held into elevated columns which are fairly easy to break. Be cautious when removing the screws.
- After removing the keyboard and the screws, use the spudger around the edges of the laptop to remove the face plate.
Use the Phillips head screw driver to remove the last 6mm screws holding the case together.
The screws are held into elevated columns which are fairly easy to break. Be cautious when removing the screws.
After removing the keyboard and the screws, use the spudger around the edges of the laptop to remove the face plate.
Step 6
- Use the Phillips head screwdriver to remove the 5mm screws on the right speaker.
- Repeat the process for the left side.
Use the Phillips head screwdriver to remove the 5mm screws on the right speaker.
Repeat the process for the left side.
Step 7
- Flip the laptop over and disconnect the black and white display wires by pulling them upwards.
- The second image shows the disconnected wires.
- Flip the laptop back over and pull the black and white wires through their holes in the motherboard.
Flip the laptop over and disconnect the black and white display wires by pulling them upwards.
The second image shows the disconnected wires.
Flip the laptop back over and pull the black and white wires through their holes in the motherboard.
Step 8
- Move the speakers out of the way after removing their holding screws.
- Remove the two 4mm screws on the hinges on each side of the laptop.
Move the speakers out of the way after removing their holding screws.
Remove the two 4mm screws on the hinges on each side of the laptop.
Step 9
- Use the screw driver to remove the two black disks from the top corners of the display.
- Remove the 5mm screws that were hidden behind the little black disks.
- Use the spudger tool to pop the cover off of the edge.
Use the screw driver to remove the two black disks from the top corners of the display.
Remove the 5mm screws that were hidden behind the little black disks.
Use the spudger tool to pop the cover off of the edge.
Step 10
- Remove the two 3 mm screws holding the display in place. Repeat this step for both the left and right sides.
Remove the two 3 mm screws holding the display in place. Repeat this step for both the left and right sides.
Step 11
- Slide the display upwards to remove it.
Slide the display upwards to remove it.
Step 12
- Use the screw driver to remove the six 3 mm screws holding the brackets and hinges onto the display.
- Do not misplace these brackets because they will be used on the new screen.
Use the screw driver to remove the six 3 mm screws holding the brackets and hinges onto the display.
Do not misplace these brackets because they will be used on the new screen.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
Author
with 2 other contributors
Danny Amado
Member since: 10/29/2018
823 Reputation
5 Guides authored
Badges:
8
+5 more badges
Team
Baylor, Team S1-G3, Williams Fall 2018
Member of Baylor, Team S1-G3, Williams Fall 2018
BU-WILLIAMS-F18S1G3
4 Members
5 Guides authored
