Difficulty

Moderate

Steps

7

Time Required

                          20 - 30 minutes

Sections

2

  • Battery
  • 2 steps
  • Screen
  • 5 steps

Flags

1

Markup Mishap

This guide needs better markups. Help out by correcting or making some markup annotations.

  • BackToshiba Satellite M305D-S4829

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

What you need

Step 1

              Battery
  • Unlatch the battery by pushing outward on both latches.

Unlatch the battery by pushing outward on both latches.

1024

Step 2

  • Slide battery out.

Slide battery out.

Step 3

              Screen
  • Remove the four rubber coverings at the corners of the screen frame to access the screws behind them.
  • Using a Phillips #0 screwdriver, remove the four screws at the corners of the screen frame.

Remove the four rubber coverings at the corners of the screen frame to access the screws behind them.

Using a Phillips #0 screwdriver, remove the four screws at the corners of the screen frame.

Step 4

  • Now you need to remove the bezel. This is the plastic frame around the screen. Gently pull it forward, and then upward to unsnap it from where it is connected at the hinges.
  • The second picture shows what the laptop will look like thus far.

Now you need to remove the bezel. This is the plastic frame around the screen. Gently pull it forward, and then upward to unsnap it from where it is connected at the hinges.

The second picture shows what the laptop will look like thus far.

Step 5

  • Turn the laptop around so that you can view the lid. Gently pull the lid away from the screen so that you can view the white clips near the base of the screen, as shown in the picture.
  • Un-clip the three connections to disconnect the wiring.
  • Unsnap the lid as well at this point. It pulls away just like the bezel (the plastic frame) did.

Turn the laptop around so that you can view the lid. Gently pull the lid away from the screen so that you can view the white clips near the base of the screen, as shown in the picture.

Un-clip the three connections to disconnect the wiring.

Unsnap the lid as well at this point. It pulls away just like the bezel (the plastic frame) did.

Step 6

  • Remove the tape at the spots shown in the picture to detach the screen from the ribbon.

Remove the tape at the spots shown in the picture to detach the screen from the ribbon.

Step 7

  • Turn the laptop so the screen faces you again. Remove this screw, and the corresponding screw on the left hand side.
  • Remove the four screws on the sides of the metal frame, located at the upper right and left, as well as the lower right and left.
  • The screen may now be removed, and the replacement screen may be installed.

Turn the laptop so the screen faces you again. Remove this screw, and the corresponding screw on the left hand side.

Remove the four screws on the sides of the metal frame, located at the upper right and left, as well as the lower right and left.

The screen may now be removed, and the replacement screen may be installed.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

Author

                                      with 1 other contributor 


                    Allison Collard

Member since: 03/12/2014

111 Reputation

                                      1 Guide authored                  



                       Badges:
                       3

Team

                       UMass Dartmouth, Team 2-4, Vijaybhaskar Spring 2014                        

                                                  Member of UMass Dartmouth, Team 2-4, Vijaybhaskar Spring 2014 



                    UMASSD-VIJAYBHASKAR-S14S2G4                     


                                            4 Members                     


                                            1 Guide authored