Toshiba Satellite L675D S7016 Top Case Housing Removal Repair Guide

Difficulty

Moderate

Steps

Time Required

                          10 minutes

Sections

Battery
3 steps
Back Panel Removal
2 steps
Hard Drive
1 step
Keyboard
4 steps
Top Case Housing
4 steps

Flags

BackToshiba Satellite L675D-S7016
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications

Introduction

What you need

Step 1

              Battery

Power down the computer and unplug the power adapter.

Power down the computer and unplug the power adapter.

1024

Step 2

Flip the laptop upside down. Locate the two latches on both sides of the battery.

Flip the laptop upside down. Locate the two latches on both sides of the battery.

Step 3

Slide the latch on the right outwards, releasing the lock. The latch stays unlocked once moved.
Simultaneously slide the latch on the left outwards while pulling the battery towards you.
Do not touch the metal connectors on the laptop and the battery.

Slide the latch on the right outwards, releasing the lock. The latch stays unlocked once moved.

Simultaneously slide the latch on the left outwards while pulling the battery towards you.

Do not touch the metal connectors on the laptop and the battery.

Step 4

              Back Panel Removal

Remove the single captive screw on the back panel with your Phillips #1 screwdriver.

Remove the single captive screw on the back panel with your Phillips #1 screwdriver.

Step 5

Pry the removal tab up. You will feel and hear the first clip release, popping up slightly.
Work your way around the border of the panel, releasing the rest of the clips.
Once all clips are released, lift the cover up and pull towards you.

Pry the removal tab up. You will feel and hear the first clip release, popping up slightly.

Work your way around the border of the panel, releasing the rest of the clips.

Once all clips are released, lift the cover up and pull towards you.

Step 6

              Hard Drive

Slide the hard drive to the left, using the silver tab.
Pull up the silver tab, removing the hard drive from the slot.
Do not touch the metal data pins on the hard drive or computer.

Slide the hard drive to the left, using the silver tab.

Pull up the silver tab, removing the hard drive from the slot.

Do not touch the metal data pins on the hard drive or computer.

Step 7

              Keyboard

Pry under the plastic strip, starting on the top right side of the key board with a Heavy Duty Spudger.
Once the first corner is raised, use your hand pulling upwards and release the rest of the strip.

Pry under the plastic strip, starting on the top right side of the key board with a Heavy Duty Spudger.

Once the first corner is raised, use your hand pulling upwards and release the rest of the strip.

Step 8

Remove the first 3mm screw with the Phillips #1 screwdriver.
Remove the next three 3mm screws.

Remove the first 3mm screw with the Phillips #1 screwdriver.

Remove the next three 3mm screws.

Step 9

Lift the keyboard gently . Slide it forward towards the screen and speakers. This reveals the connection needed for the next step.

Lift the keyboard gently . Slide it forward towards the screen and speakers. This reveals the connection needed for the next step.

Step 10

Use the pointed end of the Heavy-Duty Spudger and push the pins toward the screen, leaving them in this position.
Carefully slide the connector out of the port.

Use the pointed end of the Heavy-Duty Spudger and push the pins toward the screen, leaving them in this position.

Carefully slide the connector out of the port.

Step 11

              Top Case Housing

Remove the following screws with a Phillips #1 screwdriver.
Seventeen 5mm screws (recessed)
Three 2mm screws in the battery bay (flush-mounted)
Single 5mm screw does not need removal unless working on the screen

Remove the following screws with a Phillips #1 screwdriver.

Seventeen 5mm screws (recessed)

Three 2mm screws in the battery bay (flush-mounted)

Single 5mm screw does not need removal unless working on the screen

Step 12

Remove five 5mm screws with the screwdriver.

Remove five 5mm screws with the screwdriver.

Step 13

Locate the trackpad connector.
Pull the ribbon from the connector.

Locate the trackpad connector.

Pull the ribbon from the connector.

Step 14

Pry under the top case housing along the perimeter with a plastic opening tool.
Be careful and gentle with this step, the clips you are releasing here are plastic and can be broken by violent prying.

Pry under the top case housing along the perimeter with a plastic opening tool.

Be careful and gentle with this step, the clips you are releasing here are plastic and can be broken by violent prying.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      2 other people completed this guide.

Author

                                      with 6 other contributors

                    Austin Bons

Member since: 09/22/2016

1,122 Reputation

                                      8 Guides authored                  



                       Badges:
                       14







                                                        +11 more badges

Team

                       UC Davis, Team 2-2, Oliver Fall 2016                        

                                                  Member of UC Davis, Team 2-2, Oliver Fall 2016 



                    UCD-OLIVER-F16S2G2                     


                                            5 Members                     


                                            10 Guides authored

Susan Scroggs - Oct 2, 2022

Great help this tutorial helped

Introduction#

What you need#

Team#

Introduction

What you need

Team