Difficulty
Moderate
Steps
11
Time Required
15 - 30 minutes
Sections
2
- Battery
- 2 steps
- Touchpad Button
- 9 steps
Flags
3
Mismatched Prerequisites
This guide does not have a proper prerequisite guide. Help match it to its ideal partner by finding it or writing one!
Markup Mishap
This guide needs better markups. Help out by correcting or making some markup annotations.
Better Introduction
Improve this guide by completing or revising its introduction.
BackToshiba Satellite L655D-S5095
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
What you need
Step 1
Battery
- Locate the battery locks on the bottom of the laptop.
- Slide the right lock outwards, until it locks into place.
- Slide and hold the left lock outwards and hold it in place.
Locate the battery locks on the bottom of the laptop.
Slide the right lock outwards, until it locks into place.
Slide and hold the left lock outwards and hold it in place.
1024
Step 2
- While holding the lock in place, slide the battery out towards you.
While holding the lock in place, slide the battery out towards you.
Step 3
Touchpad Button
- Place device down so the bottom of it is facing you.
- Unscrew each screw located in the deep holes found around the bottom of the device as shown.
Place device down so the bottom of it is facing you.
Unscrew each screw located in the deep holes found around the bottom of the device as shown.
Step 4
- Unscrew the panel located over the RAM as shown
- Rotate the computer so the battery is now located on the top of the device. Now unscrew the single screw located at the top left of the RAM’s housing as shown
Unscrew the panel located over the RAM as shown
Rotate the computer so the battery is now located on the top of the device. Now unscrew the single screw located at the top left of the RAM’s housing as shown
Step 5
- Remove the battery.
- Unscrew the single screw closest to the center of the device, as shown in picture two.
- Remove the four screws that were previously hidden by the battery.
Remove the battery.
Unscrew the single screw closest to the center of the device, as shown in picture two.
Remove the four screws that were previously hidden by the battery.
Step 6
- Remove the disk drive located at the left of the device.
- Remove two screws that were hidden by the disk drive, as shown in picture two.
Remove the disk drive located at the left of the device.
Remove two screws that were hidden by the disk drive, as shown in picture two.
Step 7
- Now turn the device over so you can see the keyboard. Find the plastic bar located at the top of the keyboard.
- Pry this plastic cover off with the use of the plastic opening tools.
- Now unscrew the screws that are located under the plastic cover previously removed. After these are gone, remove the keyboard.
Now turn the device over so you can see the keyboard. Find the plastic bar located at the top of the keyboard.
Pry this plastic cover off with the use of the plastic opening tools.
Now unscrew the screws that are located under the plastic cover previously removed. After these are gone, remove the keyboard.
Step 8
- Remove the screws located around the area the keyboard had previously covered, as shown in the red circles.
- Before removing this cover, locate the connection indicated in the photo and disconnect it.
- Remove the cover.
Remove the screws located around the area the keyboard had previously covered, as shown in the red circles.
Before removing this cover, locate the connection indicated in the photo and disconnect it.
Remove the cover.
Step 9
- remove all screws on bottom marked F65
remove all screws on bottom marked F65
Step 10
- Turn the cover over and remove the back panel.
- Locate the button found at the lower end of the cover. Once found, remove the four screws keeping it in place.
Turn the cover over and remove the back panel.
Locate the button found at the lower end of the cover. Once found, remove the four screws keeping it in place.
Step 11
- Remove the two buses from the button by the blue tab as shown in the pictures.
- Remove the last bus from the motherboard by pulling the blue tab.
- Remove the disfunctional button from the device.
Remove the two buses from the button by the blue tab as shown in the pictures.
Remove the last bus from the motherboard by pulling the blue tab.
Remove the disfunctional button from the device.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
One other person completed this guide.
Author
with 6 other contributors
Alejandro
Member since: 03/11/2014
121 Reputation
1 Guide authored
Badges:
5
+2 more badges
Team
UMass Dartmouth, Team 4-4, Calaway Spring 2014
Member of UMass Dartmouth, Team 4-4, Calaway Spring 2014
UMASSD-CALAWAY-S14S4G4
4 Members
2 Guides authored