Difficulty
Moderate
Steps
15
Time Required
15 - 20 minutes
Sections
3
- Battery
- 3 steps
- Bottom Access Panel
- 2 steps
- LCD Display
- 10 steps
Flags
1
Featured Student Guide
This guide has been the hard work of our awesome students and is found to be exceptionally cool by the iFixit staff.
BackToshiba Satellite L45-S7423
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Battery
- Make sure the battery lock switch is switched to the unlocked position.
- The battery is unlocked when the battery lock switch is slid to the side with an image of an unlocked lock.
Make sure the battery lock switch is switched to the unlocked position.
The battery is unlocked when the battery lock switch is slid to the side with an image of an unlocked lock.
1024
Step 2
- Slide the battery release switch to the left.
- The switch is spring loaded, so you must hold the switch in place while removing the battery.
Slide the battery release switch to the left.
The switch is spring loaded, so you must hold the switch in place while removing the battery.
Step 3
- Using a finger, lift up the battery.
- The battery release switch must be held in place.
Using a finger, lift up the battery.
The battery release switch must be held in place.
Step 4
Bottom Access Panel
- Remove the 5 Phillips screws holding the panel in place.
- These screws are permanently fastened to the panel; they are designed to be removed only partially to avoid loss.
Remove the 5 Phillips screws holding the panel in place.
These screws are permanently fastened to the panel; they are designed to be removed only partially to avoid loss.
Step 5
- Use a finger to remove the panel by lifting up on the provided removal tab.
Use a finger to remove the panel by lifting up on the provided removal tab.
Step 6
LCD Display
- Remove the Phillips screw holding the panel in place and then use a finger to remove the panel.
- This screw is not designed to be completely removed, it is permanently fastened to the panel to avoid loss.
Remove the Phillips screw holding the panel in place and then use a finger to remove the panel.
This screw is not designed to be completely removed, it is permanently fastened to the panel to avoid loss.
Step 7
- With the aid of a plastic removal, disconnect the two wires attached to the wireless card.
With the aid of a plastic removal, disconnect the two wires attached to the wireless card.
Step 8
- Remove the yellow tape holding the black and the white wires in place.
Remove the yellow tape holding the black and the white wires in place.
Step 9
- Unwind the wires from the plastic tabs holding the wires in place.
Unwind the wires from the plastic tabs holding the wires in place.
Step 10
- Remove the screw holding the ground cable in place.
- One 4.5 mm Phillips screw.
Remove the screw holding the ground cable in place.
One 4.5 mm Phillips screw.
Step 11
- Disconnect the video cable connecting the display to the base of the laptop.
Disconnect the video cable connecting the display to the base of the laptop.
Step 12
- Pop off the laptop’s hinge covers using a spudger tool.
- Only a small amount of force is required. Excessive force may permanently damage the hinge covers.
Pop off the laptop’s hinge covers using a spudger tool.
Only a small amount of force is required. Excessive force may permanently damage the hinge covers.
Step 13
- Remove the two screws on the back side of the laptop holding the LCD display in place.
- Two 8.5 mm Phillips screws.
Remove the two screws on the back side of the laptop holding the LCD display in place.
Two 8.5 mm Phillips screws.
Step 14
- Remove the final two screws on the bottom side of the laptop holding the LCD display in place.
- Two 8.5 mm Phillips screws.
Remove the final two screws on the bottom side of the laptop holding the LCD display in place.
Step 15
- Carefully pull apart the LCD display from the base by pulling vertically upwards on the display.
- Be careful as you remove the display not to pull too hard on the cables as they pass through the opening.
Carefully pull apart the LCD display from the base by pulling vertically upwards on the display.
Be careful as you remove the display not to pull too hard on the cables as they pass through the opening.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
3 other people completed this guide.
Author
with 3 other contributors
Stephen Sippel
Member since: 04/16/2013
194 Reputation
9 Guides authored
Badges:
10
+7 more badges
Team
Cal Poly, Team 21-54, Johann Spring 2013
Member of Cal Poly, Team 21-54, Johann Spring 2013
CPSU-JOHANN-S13S21G54
4 Members
9 Guides authored