Difficulty
Difficult
Steps
19
Time Required
10 - 25 minutes
Sections
6
- Back Panel
- 2 steps
- Hard Drive
- 3 steps
- Fan
- 3 steps
- Heat Sink
- 2 steps
- Battery
- 3 steps
- Motherboard
- 6 steps
Flags
0
BackToshiba Satellite E45T-A4300
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Back Panel
- Remove the twelve 5 mm Phillips #1 screws from the back panel.
Remove the twelve 5 mm Phillips #1 screws from the back panel.
1024
Step 2
- Pry the back panel open with the plastic spudger or fingernails.
- Pry it gently so that the back panel does not crack.
Pry the back panel open with the plastic spudger or fingernails.
Pry it gently so that the back panel does not crack.
Step 3
Hard Drive
- Remove the three 7mm black screws using the Phillips #1 screwdriver.
Remove the three 7mm black screws using the Phillips #1 screwdriver.
Step 4
- Remove the hard drive’s connection port with grooved tweezers.
Remove the hard drive’s connection port with grooved tweezers.
Step 5
- Pull the hard drive out of the hook and remove it from the device.
Pull the hard drive out of the hook and remove it from the device.
Step 6
Fan
- Remove the two 5 mm screws using a Phillips #1 screwdriver.
Remove the two 5 mm screws using a Phillips #1 screwdriver.
Step 7
- Gently disconnect the fan cable from the device.
Gently disconnect the fan cable from the device.
Step 8
- Move the wires away from the fan’s hook.
- Remove the fan from the device.
Move the wires away from the fan’s hook.
Remove the fan from the device.
Step 9
Heat Sink
- Remove the three 5 mm screws using a Phillips #1 screwdriver.
Remove the three 5 mm screws using a Phillips #1 screwdriver.
Step 10
- Pry the heat sink away from the laptop with two hands at both ends and remove it from the device.
- The heat sink is glued to a gray paste called thermal paste. Do not touch the paste.
Pry the heat sink away from the laptop with two hands at both ends and remove it from the device.
The heat sink is glued to a gray paste called thermal paste. Do not touch the paste.
Step 11
Battery
- Disconnect the battery connector from the motherboard.
Disconnect the battery connector from the motherboard.
Step 12
- Remove the single screw Phillips #1 screw near the battery.
Remove the single screw Phillips #1 screw near the battery.
Step 13
- Remove the battery from the laptop.
Remove the battery from the laptop.
Step 14
Motherboard
- Remove the single 7 mm silver screw using a Phillips #1 screwdriver.
Remove the single 7 mm silver screw using a Phillips #1 screwdriver.
Step 15
- Pull metal stick holder until it is upright.
Pull metal stick holder until it is upright.
Step 16
- Remove the 7 mm silver screw under the metal bar using the Phillips #1 screwdriver.
Remove the 7 mm silver screw under the metal bar using the Phillips #1 screwdriver.
Step 17
- Disconnect the six connectors from the device.
- For the monitor port, pull it from the black tab.
- For the connection port with the blue strip, lift the white placeholder before pulling the blue strip out of the connection port.
Disconnect the six connectors from the device.
For the monitor port, pull it from the black tab.
For the connection port with the blue strip, lift the white placeholder before pulling the blue strip out of the connection port.
Step 18
- Pull out 2 plugs out from the wireless network card.
Pull out 2 plugs out from the wireless network card.
Step 19
- Remove the motherboard from the device.
Remove the motherboard from the device.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
Author
with 2 other contributors
James Nguyen
Member since: 10/23/2018
564 Reputation
5 Guides authored
Badges:
9
+6 more badges
Team
UMass Dartmouth, Team S1-G4, Simcock Fall 2018
Member of UMass Dartmouth, Team S1-G4, Simcock Fall 2018
UMASSD-SIMCOCK-F18S1G4
3 Members
14 Guides authored