Difficulty

Moderate

Steps

17

Time Required

                          20 minutes            

Sections

4

  • Battery
  • 7 steps
  • Heat Sync Fan
  • 4 steps
  • Wifi Card
  • 3 steps
  • Motherboard
  • 3 steps

Flags

0

  • BackToshiba Satellite Click 2 Pro

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

What you need

Step 1

              Battery               
  • Working on your device while it is turned on may result in electric shock. Make sure to shut down and unplug your device before you begin.
  • Push down on the tablet sides until you feel a click, then pull up.
  • This will separate the tablet from the detachable base, make sure to hold down the keyboard for easier detachment.

Working on your device while it is turned on may result in electric shock. Make sure to shut down and unplug your device before you begin.

Push down on the tablet sides until you feel a click, then pull up.

This will separate the tablet from the detachable base, make sure to hold down the keyboard for easier detachment.

1024

Step 2

  • Remove the base of the tablet from the screen using a plastic opening tool.
  • Make sure to separate the base evenly on both sides when removing it from the screen.

Remove the base of the tablet from the screen using a plastic opening tool.

Make sure to separate the base evenly on both sides when removing it from the screen.

Step 3

  • Remove the battery power connector using ESD safe tweezers.

Remove the battery power connector using ESD safe tweezers.

Step 4

  • Remove the LED ribbon cable using ESD safe tweezers.
  • Remove the SIM card ribbon cable using ESD safe tweezers.
  • Remove the Docking connector ribbon cable using plastic opening tool.
  • The ribbons may be stuck to the battery so make sure to peel off gently to prevent damage.
  • Make sure to flip up the white connector attached to the LED and Sim Card ribbons before removing them .

Remove the LED ribbon cable using ESD safe tweezers.

Remove the SIM card ribbon cable using ESD safe tweezers.

Remove the Docking connector ribbon cable using plastic opening tool.

The ribbons may be stuck to the battery so make sure to peel off gently to prevent damage.

Make sure to flip up the white connector attached to the LED and Sim Card ribbons before removing them .

Step 5

  • Remove the LCD Display ribbon cable using a plastic opening tool.
  • Remove the I/O ribbon cable using a plastic opening tool.
  • The ribbons may be stuck to the battery so make sure to peel them off gently to prevent damage.

Remove the LCD Display ribbon cable using a plastic opening tool.

Remove the I/O ribbon cable using a plastic opening tool.

The ribbons may be stuck to the battery so make sure to peel them off gently to prevent damage.

Step 6

  • Remove five 3.5mm Phillips J0 screws using a Phillips screw driver.

Remove five 3.5mm Phillips J0 screws using a Phillips screw driver.

Step 7

  • Remove the battery from its holding position.

Remove the battery from its holding position.

Step 8

              Heat Sync Fan               
  • Remove the power connector from the fan using a pair of tweezers.

Remove the power connector from the fan using a pair of tweezers.

Step 9

  • Remove two 3.0mm Phillips J0 screws using a Phillips screw driver.

Remove two 3.0mm Phillips J0 screws using a Phillips screw driver.

Step 10

  • Remove four 3.5mm Phillips J0 screws from the heat sink.

Remove four 3.5mm Phillips J0 screws from the heat sink.

Step 11

  • Remove the heat sink fan.
  • The heat sink cover may be hard to peel off the first time due to the adhesive.

Remove the heat sink fan.

The heat sink cover may be hard to peel off the first time due to the adhesive.

Step 12

              Wifi Card               
  • Remove the 3mm screw J0 Phillips screw with the Philips screw driver.

Remove the 3mm screw J0 Phillips screw with the Philips screw driver.

Step 13

  • Remove the black and white cables attached using ESD safe tweezers.

Remove the black and white cables attached using ESD safe tweezers.

Step 14

  • Remove wifi card.

Remove wifi card.

Step 15

              Motherboard               
  • Locate and remove the five connectors using ESD safe tweezers.

Locate and remove the five connectors using ESD safe tweezers.

Step 16

  • Remove the four 3.0mm Phillips J0 screws using a Phillips screw driver.

Remove the four 3.0mm Phillips J0 screws using a Phillips screw driver.

Step 17

  • Remove the motherboard.

Remove the motherboard.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      3 other people completed this guide.                                             

Author

                                      with 2 other contributors 

                    Paul DeOrsey                     

Member since: 03/10/2016

893 Reputation

                                      5 Guides authored                  



                       Badges:
                       13







                                                        +10 more badges                           

Team

                       UMass Dartmouth, Team 4-3, Catania Spring 2016                        

                                                  Member of UMass Dartmouth, Team 4-3, Catania Spring 2016 



                    UMASSD-CATANIA-S16S4G3                     


                                            3 Members                     


                                            10 Guides authored