Difficulty

Easy

Steps

8

Time Required

                          5 minutes

Sections

2

  • Battery
  • 5 steps
  • RAM
  • 3 steps

Flags

1

This guide has been the hard work of our awesome students and is found to be exceptionally cool by the iFixit staff.

  • BackToshiba Satellite C875-S7304

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

RAM is an important hardware component that allows data to be read or written in the same time regardless of the location of said data inside the memory. Faulty RAM can result in blue screens of death (BSODs), error messages, diminished performance, untimely reboots, or freezes.

Review the troubleshooting page before using this guide. Some issues may be resolved through something as simple as a software update.

If you want to enhance your computer’s performance, you may want to upgrade your RAM. This device supports RAM in capacities ranging from 4 GB to 16 GB. Each RAM stick must be DDR3 1600 MHz and be between 4 GB and 8GB.

Disconnect the laptop from any external power source and power off your laptop completely before beginning RAM replacement.

What you need

Step 1

              Battery
  • Power off and unplug the charger from your device.
  • Carefully flip your device upside down laying it onto a flat surface with the battery facing you.
  • The two eject switches are located on the right and left side of the battery compartment.

Power off and unplug the charger from your device.

Carefully flip your device upside down laying it onto a flat surface with the battery facing you.

The two eject switches are located on the right and left side of the battery compartment.

1024

Step 2

  • Slide the right switch further towards the right to lock it into place.

Slide the right switch further towards the right to lock it into place.

Step 3

  • Slide the switch to the left. Continue to push the switch because unlike the right switch, it will not lock into place.

Slide the switch to the left. Continue to push the switch because unlike the right switch, it will not lock into place.

Step 4

  • Using both hands, continue to push the left switch and grasp onto the center notch located in between the right and left switch.
  • Pull the center notch towards you and you will notice the battery will start to eject.

Using both hands, continue to push the left switch and grasp onto the center notch located in between the right and left switch.

Pull the center notch towards you and you will notice the battery will start to eject.

Step 5

  • Lift the battery out carefully using two hands.

Lift the battery out carefully using two hands.

Step 6

              RAM
  • Use a Phillips #1 to unscrew one 7.0 mm screw from the hard drive/RAM panel.
  • You cannot remove the screw from the panel. Simply unscrew it until loosened.

Use a Phillips #1 to unscrew one 7.0 mm screw from the hard drive/RAM panel.

You cannot remove the screw from the panel. Simply unscrew it until loosened.

Step 7

  • Wedge the plastic opening tool between the back panel and the hard drive/RAM panel near the screw.
  • Lift the end of the opening tool slowly until the hard drive/RAM panel separates on one side.
  • Repeat the steps above on the left side of the hard drive/RAM panel.
  • Pull the cover towards you and up from the device to remove it.
  • Hearing a popping noise while wedging the plastic opening tool is normal.

Wedge the plastic opening tool between the back panel and the hard drive/RAM panel near the screw.

Lift the end of the opening tool slowly until the hard drive/RAM panel separates on one side.

Repeat the steps above on the left side of the hard drive/RAM panel.

Pull the cover towards you and up from the device to remove it.

Hearing a popping noise while wedging the plastic opening tool is normal.

Step 8

  • Push outward on the metal tabs to unclasp the RAM from its slot.
  • With the RAM unclasped at a slight angle, carefully pull it out with two hands.
  • When reassembling, remember to align the indentation on the RAM with the indentation on its slot.

Push outward on the metal tabs to unclasp the RAM from its slot.

With the RAM unclasped at a slight angle, carefully pull it out with two hands.

When reassembling, remember to align the indentation on the RAM with the indentation on its slot.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      2 other people completed this guide.

Author

                                      with 1 other contributor 


                    Taimoor Arshad

Member since: 09/04/2019

363 Reputation

                                      2 Guides authored                  



                       Badges:
                       8







                                                        +5 more badges

Team

                       University of Alabama, Team S2-G5, Bedsole Fall 2019                        

                                                  Member of University of Alabama, Team S2-G5, Bedsole Fall 2019 



                    UA-BEDSOLE-F19S2G5                     


                                            4 Members                     


                                            10 Guides authored