Difficulty

Easy

Steps

22

Time Required

                          8 minutes

Sections

2

  • Keyboard
  • 18 steps
  • Fan
  • 4 steps

Flags

0

  • BackToshiba Satellite C55D-B5310

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

What you need

Step 1

              Keyboard
  • Turn off your device before starting.
  • Flip the phone over so that the back camera is facing you.

Turn off your device before starting.

Flip the phone over so that the back camera is facing you.

1024

Step 2

  • Use a your hands to remove the backing of the phone.

Use a your hands to remove the backing of the phone.

Step 3

  • Use your phillips screwdriver to begin removing all the accesible screws.

Use your phillips screwdriver to begin removing all the accesible screws.

Step 4

  • Now begin to remove the coverings above and below the middle plate with your hand.

Now begin to remove the coverings above and below the middle plate with your hand.

Step 5

  • use your hand or a tool to remove the tabbing on the metal plate covering the battery.

use your hand or a tool to remove the tabbing on the metal plate covering the battery.

Step 6

  • Remove the metal plate covering the battery.

Remove the metal plate covering the battery.

Step 7

  • Use your wedging tool to begin removeing the adhesive under the battery.

Use your wedging tool to begin removeing the adhesive under the battery.

Step 8

  • Remove these two screws with your phillips screw driver.

Remove these two screws with your phillips screw driver.

Step 9

  • Open the two metal tabs

Open the two metal tabs

Step 10

  • Flip the phone back over with the screen facing you.

Flip the phone back over with the screen facing you.

Step 11

  • Begin to use the wedging tool to remove the space bar off of the keyboard.

Begin to use the wedging tool to remove the space bar off of the keyboard.

Step 12

  • remove the screws on each end of the space bars vacant lcoation.

remove the screws on each end of the space bars vacant lcoation.

Step 13

  • Grab the wedging tool and begin wedging the old keyboard.

Grab the wedging tool and begin wedging the old keyboard.

Step 14

  • begind wedging the back of the keyboard until free.

begind wedging the back of the keyboard until free.

Step 15

  • Begin deperating the keyboard from the backing.

Begin deperating the keyboard from the backing.

Step 16

  • grab your replacement keyboard and connect it to the backing of the old keyboard.

grab your replacement keyboard and connect it to the backing of the old keyboard.

Step 17

  • place the keyboard back onto the front of the phone

place the keyboard back onto the front of the phone

Step 18

  • once placed, hold the keyboard onto the phone while clicking the two metal plates back down to connect the keyboard.

once placed, hold the keyboard onto the phone while clicking the two metal plates back down to connect the keyboard.

Step 19

              Fan
  • Remove the remaining thirteen 7 mm Phillips screws holding the back cover using the PH1 bit and Magnetic Driver.

Remove the remaining thirteen 7 mm Phillips screws holding the back cover using the PH1 bit and Magnetic Driver.

Step 20

  • Using the plastic opening tools, separate the back cover from the laptop.
  • It is recommended that you start from a corner and run the tool along the edge of the cover.
  • Be careful not to bend or crack the plastic back cover.

Using the plastic opening tools, separate the back cover from the laptop.

It is recommended that you start from a corner and run the tool along the edge of the cover.

Be careful not to bend or crack the plastic back cover.

Step 21

  • Remove the three 3 mm Phillips screws holding the fan cable in place using the PH1 bit and Magnetic Driver.
  • Lift the fan cable connector from the fan.

Remove the three 3 mm Phillips screws holding the fan cable in place using the PH1 bit and Magnetic Driver.

Lift the fan cable connector from the fan.

Step 22

  • Remove the fan from the plug by releasing the clamps located on each side of the socket.
  • Slide the connector out of the socket.
  • Lift the computer fan from the motherboard.

Remove the fan from the plug by releasing the clamps located on each side of the socket.

Slide the connector out of the socket.

Lift the computer fan from the motherboard.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

Author

                                      with 2 other contributors 


                    Crystal Loomis

Member since: 01/22/2018

720 Reputation

                                      5 Guides authored                  



                       Badges:
                       11







                                                        +8 more badges

Team

                       South Arkansas Community College, Team S1-G1, Mitchell Spring 2018                        

                                                  Member of South Arkansas Community College, Team S1-G1, Mitchell Spring 2018 



                    SACC-MITCHELL-S18S1G1                     


                                            4 Members                     


                                            12 Guides authored