Difficulty

Difficult

Steps

11

Time Required

                          30 minutes            

Sections

4

  • Battery
  • 1 step
  • Keyboard
  • 4 steps
  • Casing
  • 3 steps
  • Speakers
  • 3 steps

Flags

0

  • BackToshiba Satellite A105-S4284

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

What you need

Step 1

              Battery               
  • Make sure your computer is turned off and the computer is not plugged in.
  • Turn your laptop upside down, and slide the right release tab outward.
  • Using you left hand, hold the left release tab towards the left side and then pull the battery out.

Make sure your computer is turned off and the computer is not plugged in.

Turn your laptop upside down, and slide the right release tab outward.

Using you left hand, hold the left release tab towards the left side and then pull the battery out.

1024

Step 2

              Keyboard               
  • Flip the laptop over so it is rightside up, and open the laptop all the way so that the screen is horizontal.

Flip the laptop over so it is rightside up, and open the laptop all the way so that the screen is horizontal.

Step 3

  • Using the plastic opening tool, pry off the panel above the keyboard, starting near the right front speaker.
  • Use the plastic opening tool to pop off tabs along the length of this panel.
  • This may feel like you’re about to break something, but as long as you work your way down the panel and don’t yank it out, the laptop will be fine.

Using the plastic opening tool, pry off the panel above the keyboard, starting near the right front speaker.

Use the plastic opening tool to pop off tabs along the length of this panel.

This may feel like you’re about to break something, but as long as you work your way down the panel and don’t yank it out, the laptop will be fine.

Step 4

  • Unscrew the two 4.5 mm screws holding the keyboard on with the Phillips #1 screwdriver.

Unscrew the two 4.5 mm screws holding the keyboard on with the Phillips #1 screwdriver.

Step 5

  • Lift the keyboard gently from the side closest the screen.
  • Pull out the ribbon connecting the keyboard to the laptop.

Lift the keyboard gently from the side closest the screen.

Pull out the ribbon connecting the keyboard to the laptop.

Step 6

              Casing               
  • Disconnect wire attaching LCD to motherboard
  • Using the Phillips screwdriver remove the two 4.0mm screws from each hinge above speakers
  • Partially close the lid and remove the last two 4.0mm screws from the back of the laptop.

Disconnect wire attaching LCD to motherboard

Using the Phillips screwdriver remove the two 4.0mm screws from each hinge above speakers

Partially close the lid and remove the last two 4.0mm screws from the back of the laptop.

Step 7

  • Remove the seventeen 4.5mm phillips screws on the bottom of the laptop.
  • Using the pry tool separate the two halves of the laptop base.
  • Use caution when separating the laptop halves as they are still connected by two ribbon cables.

Remove the seventeen 4.5mm phillips screws on the bottom of the laptop.

Using the pry tool separate the two halves of the laptop base.

Use caution when separating the laptop halves as they are still connected by two ribbon cables.

Step 8

  • Lift the top half of the case enough to get your hand beneath it, and then remove the two ribbon cables that connect it to the motherboard.

Lift the top half of the case enough to get your hand beneath it, and then remove the two ribbon cables that connect it to the motherboard.

Step 9

              Speakers               
  • Remove the lower half of the laptop and lay upper half on its top.

Remove the lower half of the laptop and lay upper half on its top.

Step 10

  • Using the Phillips screwdriver remove the two 4.0mm screws holding each of the speakers housings to the case.
  • Remove the speakers from the case being careful of the wires.

Using the Phillips screwdriver remove the two 4.0mm screws holding each of the speakers housings to the case.

Remove the speakers from the case being careful of the wires.

Step 11

  • The wires for the speakers are color coded.The red and black wires are for the right speaker, and the black and white wires are for the left speaker.

The wires for the speakers are color coded.The red and black wires are for the right speaker, and the black and white wires are for the left speaker.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      One other person completed this guide.                                             

Author

                                      with 3 other contributors 

                    Josh                     

Member since: 03/12/2014

625 Reputation

                                      5 Guides authored                  



                       Badges:
                       8







                                                        +5 more badges                           

Team

                       UMass Dartmouth, Team 1-6, Cichon Spring 2014                        

                                                  Member of UMass Dartmouth, Team 1-6, Cichon Spring 2014 



                    UMASSD-CICHON-S14S1G6                     


                                            3 Members                     


                                            6 Guides authored