Difficulty
Easy
Steps
6
Time Required
10 minutes
Sections
1
- Battery
- 6 steps
Flags
Better Introduction
Improve this guide by completing or revising its introduction.
BackToshiba Encore WT8-A
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
What you need
Step 1
Battery
- Use the metal spudger to create a gap between the back cover and the device.
- Be gentle when using the metal spudger so that the casing is not damaged.
Use the metal spudger to create a gap between the back cover and the device.
Be gentle when using the metal spudger so that the casing is not damaged.
1024
Step 2
- Use the nylon spudger to completely separate the back of the device.
- Take the nylon spudger around the outside of the device cover until it comes free.
Use the nylon spudger to completely separate the back of the device.
Take the nylon spudger around the outside of the device cover until it comes free.
Step 3
- Use the Phillips head PH0 to remove the 7 battery screws.
- The 5 side screws measure 3.5mm.
- The 2 top and bottom screws measure 4.5 mm.
Use the Phillips head PH0 to remove the 7 battery screws.
The 5 side screws measure 3.5mm.
The 2 top and bottom screws measure 4.5 mm.
Step 4
- To disconnect the cable, use the fine tweezers to flip up the small retaining flap. Then, you can safely pull the ribbon cable out.
- Be sure you are prying up on the hinged retaining flap, not the connector itself.
- The zero insertion force (ZIF) connector is used to secure delicate ribbon cables, such as this trackpad cable.
To disconnect the cable, use the fine tweezers to flip up the small retaining flap. Then, you can safely pull the ribbon cable out.
Be sure you are prying up on the hinged retaining flap, not the connector itself.
The zero insertion force (ZIF) connector is used to secure delicate ribbon cables, such as this trackpad cable.
Step 5
- Remove the colored power cable from its connector.
- To disconnect it safely, use the pointed tip of a spudger to carefully push on each side of the connector.
- Alternating from one side to the other, gently “walk” the connector out of its socket.
- Be sure to be very gentle when prying colored wires from motherboard to ensure that there is no damage.
Remove the colored power cable from its connector.
To disconnect it safely, use the pointed tip of a spudger to carefully push on each side of the connector.
Alternating from one side to the other, gently “walk” the connector out of its socket.
Be sure to be very gentle when prying colored wires from motherboard to ensure that there is no damage.
Step 6
- Battery will lift out of the device.
Battery will lift out of the device.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
2 other people completed this guide.
Author
with 3 other contributors
Zachary Armstrong
Member since: 09/15/2016
281 Reputation
2 Guides authored
Badges:
12
+9 more badges
Team
USF Tampa, Team 17-4, Blackwell Fall 2016
Member of USF Tampa, Team 17-4, Blackwell Fall 2016
USFT-BLACKWELL-F16S17G4
3 Members
8 Guides authored
Ravindra MIstry - Sep 29, 2017
Reply
Hi can I get Battery for Toshiba Encore 2 WT8-B?
Thanks
Regards
Dr Ravindra
Hi friends can I get Battery for Toshiba Encore 2 WT8-B
monzer daoud - Jan 27, 2022
Reply
who can I replacement socket charging for toshiba tablet WT8-A
