Difficulty
Moderate
Steps
13
Time Required
10 - 15 minutes
Sections
2
- Battery
- 5 steps
- Front-Facing Camera
- 8 steps
Flags
0
BackToshiba Encore Mini
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Battery
- To replace the battery, the rear cover must first be removed.
- Using the flat end of the spudger, gently pry open the back case from the rest of the device.
- It may be easier to start along one of the long edges and carefully work your way toward the corner, then along the short edge.
To replace the battery, the rear cover must first be removed.
Using the flat end of the spudger, gently pry open the back case from the rest of the device.
It may be easier to start along one of the long edges and carefully work your way toward the corner, then along the short edge.
1024
Step 2
- Remove the rear cover and set it aside.
Remove the rear cover and set it aside.
Step 3
- Carefully remove the electrical tape that holds the battery in place.
Carefully remove the electrical tape that holds the battery in place.
Step 4
- Using needle-nose tweezers, gently push the large white wire connector (connected to the black, red and blue wires) out of its housing.
Using needle-nose tweezers, gently push the large white wire connector (connected to the black, red and blue wires) out of its housing.
Step 5
- Gently lift the battery out of the device.
- Be careful not to pull on the connecting wires.
Gently lift the battery out of the device.
Be careful not to pull on the connecting wires.
Step 6
Front-Facing Camera
- The audio module must be removed to replace the front-facing camera.
- Using needle-nose tweezers, carefully push the small white wire connector (red/black wires) out of its housing.
- Gently remove red/black wire strands from the clips holding them to the back of the screen.
The audio module must be removed to replace the front-facing camera.
Using needle-nose tweezers, carefully push the small white wire connector (red/black wires) out of its housing.
Gently remove red/black wire strands from the clips holding them to the back of the screen.
Step 7
- Gently pry audio module from the back of the screen using tweezers and spudger. Be careful not to pull on the wires.
- Adhesive on the bottom of the speaker module may make it difficult to remove.
- Set the audio module and attached wire aside.
Gently pry audio module from the back of the screen using tweezers and spudger. Be careful not to pull on the wires.
Adhesive on the bottom of the speaker module may make it difficult to remove.
Set the audio module and attached wire aside.
Step 8
- Using needle-nose tweezers, carefully flip up the dark gray cover on the right of the device holding the small orange ribbon in place. (It is approximately 1/4" wide.)
- With the tweezers, carefully pull the small ribbon out of its housing. It will stay attached to the device at the other end.
Using needle-nose tweezers, carefully flip up the dark gray cover on the right of the device holding the small orange ribbon in place. (It is approximately 1/4" wide.)
With the tweezers, carefully pull the small ribbon out of its housing. It will stay attached to the device at the other end.
Step 9
- A wide orange/gold ribbon connects the screen to the motherboard. (Ribbon is approximately 1" wide.)
- Carefully pull the black tape off the ribbon housing and set it aside. You will need to replace the tape when reassembling the device.
A wide orange/gold ribbon connects the screen to the motherboard. (Ribbon is approximately 1" wide.)
Carefully pull the black tape off the ribbon housing and set it aside. You will need to replace the tape when reassembling the device.
Step 10
- Damaging this ribbon will permanently disable your device!
- Using needle-nose tweezers, carefully flip up the dark gray cover.
- With the tweezers, carefully pull the wide ribbon from its housing. It will stay attached to the device at the other end.
Damaging this ribbon will permanently disable your device!
Using needle-nose tweezers, carefully flip up the dark gray cover.
With the tweezers, carefully pull the wide ribbon from its housing. It will stay attached to the device at the other end.
Step 11
- Using a Phillips 000 screwdriver, remove the screws holding components together.
- Remove four 4.2 mm Phillips screws.
- Remove one 3mm Phillips screw.
Using a Phillips 000 screwdriver, remove the screws holding components together.
Remove four 4.2 mm Phillips screws.
Remove one 3mm Phillips screw.
Step 12
- Holding the motherboard carefully by the edges, gently lift it up off the screen and carefully set it aside.
- The motherboard may resist as you try to lift it –this is normal.
Holding the motherboard carefully by the edges, gently lift it up off the screen and carefully set it aside.
The motherboard may resist as you try to lift it –this is normal.
Step 13
- The front-facing camera may dislodge freely when removing the motherboard.
- If camera has not already “popped” off the motherboard, use needle-nose tweezers to gently grasp the camera and remove from motherboard.
The front-facing camera may dislodge freely when removing the motherboard.
If camera has not already “popped” off the motherboard, use needle-nose tweezers to gently grasp the camera and remove from motherboard.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
Author
with 3 other contributors
Shirley Low
Member since: 07/09/2015
143 Reputation
1 Guide authored
Badges:
6
+3 more badges
Team
UW Tacoma, Team 1-3, Liner SU 2015
Member of UW Tacoma, Team 1-3, Liner SU 2015
UWT-LINER-SU15S1G3
4 Members
6 Guides authored
