Difficulty
Very easy
Steps
11
Time Required
5 minutes
Sections
3
- Back Cover
- 4 steps
- Battery
- 4 steps
- Speakers
- 3 steps
Flags
1
Better Introduction
Improve this guide by completing or revising its introduction.
BackToshiba CB35-C3300 Chromebook 2
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Back Cover
- Remove the 2 rubber foot pads from the bottom (opposite the hinge) with the small Plastic Opening tool.
Remove the 2 rubber foot pads from the bottom (opposite the hinge) with the small Plastic Opening tool.
1024
Step 2
- Remove the 10 7.1 mm screws using Phillips #1 screwdriver.
Remove the 10 7.1 mm screws using Phillips #1 screwdriver.
Step 3
- Loosen the back cover by using a plastic opening tool all the way around the device.
- There are areas all along the sides of the device that help aid in this.
- Be careful when prying, and go slow. The silver plastic frame around the dull gray plastic bottom is fragile and easily dented from prying pressure.
Loosen the back cover by using a plastic opening tool all the way around the device.
There are areas all along the sides of the device that help aid in this.
Be careful when prying, and go slow. The silver plastic frame around the dull gray plastic bottom is fragile and easily dented from prying pressure.
Step 4
- Remove the back cover by gently lifting up on one side of the device.
- The easiest side to lift up on is the one with the removed rubber foot pads.
Remove the back cover by gently lifting up on one side of the device.
The easiest side to lift up on is the one with the removed rubber foot pads.
Step 5
Battery
- Remove the tape holding the speaker wire to the battery on both sides using a small opening tool.
Remove the tape holding the speaker wire to the battery on both sides using a small opening tool.
Step 6
- Remove the 4 Phillips 3.2 mm screws holding the battery in place, with the Phillips #1 screwdriver.
Remove the 4 Phillips 3.2 mm screws holding the battery in place, with the Phillips #1 screwdriver.
Step 7
- To disconnect the wire from the mother board, gently press down with the flat end of Spudger and pull on the wire.
- Gently shaking the wire from left to right helps with the wire removal
To disconnect the wire from the mother board, gently press down with the flat end of Spudger and pull on the wire.
Gently shaking the wire from left to right helps with the wire removal
Step 8
- Remove the battery by gently pulling on the bottom corners.
- Be careful to move the battery’s wire under the speaker’s wire.
Remove the battery by gently pulling on the bottom corners.
Be careful to move the battery’s wire under the speaker’s wire.
Step 9
Speakers
- Remove the 4 Phillip 6.3 mm screws from both the right and left speakers using Phllips 1 screwdriver.
Remove the 4 Phillip 6.3 mm screws from both the right and left speakers using Phllips 1 screwdriver.
Step 10
- Gently remove wire from the motherboard by pulling it out of the connector socket.
Gently remove wire from the motherboard by pulling it out of the connector socket.
Step 11
- Remove the right and left speaker by lifting them up.
Remove the right and left speaker by lifting them up.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
Author
with 2 other contributors
Mehdi Mohammadi
Member since: 10/18/2017
416 Reputation
1 Guide authored
Badges:
5
+2 more badges
Team
USF Tampa, Team S1-G121, Cagle Fall 2017
Member of USF Tampa, Team S1-G121, Cagle Fall 2017
USFT-CAGLE-F17S1G121
3 Members
14 Guides authored