Difficulty
Difficult
Steps
12
Time Required
20 - 30 minutes
Sections
4
- Casing
- 2 steps
- Battery
- 3 steps
- Wheel
- 2 steps
- Motor
- 5 steps
Flags
0
BackTorque King Electric RTR RC Monster Truck
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Casing
- From the top view, remove each of the four pins that hold the casing in place.
From the top view, remove each of the four pins that hold the casing in place.
1024
Step 2
- Slowly pull the casing up to remove it.
Slowly pull the casing up to remove it.
Step 3
Battery
- Beginning at the bottom of the truck, twist the release clip on the casing until the release clip is no longer covering the battery casing.
Beginning at the bottom of the truck, twist the release clip on the casing until the release clip is no longer covering the battery casing.
Step 4
- Next, use a Phillips 00 screwdriver to remove the 8mm screw on the battery casing and remove the battery casing.
Next, use a Phillips 00 screwdriver to remove the 8mm screw on the battery casing and remove the battery casing.
Step 5
- Do not skip this step if you are continuing onto the next step, you will risk electric shock.
- Finally, remove the battery from the white connector by squeezing the clip on the connector while pulling.
Do not skip this step if you are continuing onto the next step, you will risk electric shock.
Finally, remove the battery from the white connector by squeezing the clip on the connector while pulling.
Step 6
Removing Screws
- Using a Phillips 1 screwdriver, completely unscrew the 8mm screw located in the center of the wheel. Repeat this step for other wheels if needed.
Using a Phillips 1 screwdriver, completely unscrew the 8mm screw located in the center of the wheel. Repeat this step for other wheels if needed.
Step 7
Removing the Wheel
- Carefully pull the wheel off of its axle. Repeat for other wheels as necessary.
Carefully pull the wheel off of its axle. Repeat for other wheels as necessary.
Step 8
Motor
- After removing the rear wheels, use a Phillips #1 screwdriver to remove the two 11m screws indicated.
After removing the rear wheels, use a Phillips #1 screwdriver to remove the two 11m screws indicated.
Step 9
- Remove the cap to reveal the motor.
Remove the cap to reveal the motor.
Step 10
- Remove the metal piece that clasps the motor in place.
Remove the metal piece that clasps the motor in place.
Step 11
- Carefully pull out the motor from the chassis.
Carefully pull out the motor from the chassis.
Step 12
- Warning: Ensure that the battery is properly removed before attempting this step. If you attempt this step with the battery in you risk injury by electric shock and damage to the truck.
- Desolder the red and black wires from the motor. Note where each wire is supposed to connect.
- Caution: Do not desolder the small orange capacitor.
Warning: Ensure that the battery is properly removed before attempting this step. If you attempt this step with the battery in you risk injury by electric shock and damage to the truck.
Desolder the red and black wires from the motor. Note where each wire is supposed to connect.
Caution: Do not desolder the small orange capacitor.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
One other person completed this guide.
Author
with 3 other contributors
Maximiliano Cortes
Member since: 02/01/2015
418 Reputation
3 Guides authored
Badges:
9
+6 more badges
Team
Cal Poly, Team 6-30, Amido Winter 2015
Member of Cal Poly, Team 6-30, Amido Winter 2015
CPSU-AMIDO-W15S6G30
4 Members
8 Guides authored
Beth Bishop - Jul 2, 2017
Reply
My favorite trucks were Chalkboard Chuck and Samson, but I took pictures of several of the trucks and tried repeatedly to snap the perfect picture. {Obviously my perfect pics are a bit fuzzy.}
In addition to the big-honking Monster Trucks we also got to see some daring and dangerous motorcycle stunts!
