Featured
Featured Guide
Difficulty
Easy
Steps
9
Time Required
30 - 45 minutes
Sections
2
- Toniebox Opening Procedure
- 4 steps
- Battery
- 5 steps
Flags
1
Featured Guide
This guide has been found to be exceptionally cool by the iFixit staff.
BackToniebox
Full Screen
Options
History
Save to Favorites
Download PDF
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Toniebox Opening Procedure
- Put the Toniebox on a flat surface (e.g. a desk or a workbench).
- Apply some pressure and turn the Toniebox counterclockwise to unlock the two clips beneath the bottom plate.
- You will hear a “klick” when the two clips unlock.
Put the Toniebox on a flat surface (e.g. a desk or a workbench).
Apply some pressure and turn the Toniebox counterclockwise to unlock the two clips beneath the bottom plate.
You will hear a “klick” when the two clips unlock.
1024
Step 2
- Remove the bottom plate.
Remove the bottom plate.
Step 3
- Remove the Phillips #1 screw on the bottom of the Toniebox.
Remove the Phillips #1 screw on the bottom of the Toniebox.
Step 4
- Lift the inner part out of the foam housing.
Lift the inner part out of the foam housing.
Step 5
Battery
- Unplug the battery connector from the main board by gently pulling the cables.
- When reconnecting the new battery make sure to properly orient the connector.
Unplug the battery connector from the main board by gently pulling the cables.
When reconnecting the new battery make sure to properly orient the connector.
Step 6
- Losen the two screws next to the battery. Don’t remove them.
- Lift the main board a bit to widen the gap between the white plastic housing.
- This gap will help you in the next step.
Losen the two screws next to the battery. Don’t remove them.
Lift the main board a bit to widen the gap between the white plastic housing.
This gap will help you in the next step.
Step 7
- Feed the battery cable from behind the main board and out of its plastic guide hooks.
- When installing the new battery you don’t have to feed the cable behind the main board. Depending on their length aligning them along the black plastic will suffice.
Feed the battery cable from behind the main board and out of its plastic guide hooks.
When installing the new battery you don’t have to feed the cable behind the main board. Depending on their length aligning them along the black plastic will suffice.
Step 8
- Use a spudger or finger to push down the plastic latch that keeps the battery in place.
- Push the battery out of its frame.
Use a spudger or finger to push down the plastic latch that keeps the battery in place.
Push the battery out of its frame.
Step 9
- Remove the battery.
Remove the battery.
To reassemble your device, follow these instructions in reverse order.
Take your e-waste to an R2 or e-Stewards certified recycler.
Cancel: I did not complete this guide.
28 other people completed this guide.
Tobias Isakeit is helping us fix the world! Want to contribute? Start translating ›
Special thanks to these translators:
100%
Tobias Isakeit
Author
Tobias Isakeit
Member since: 03/31/2014
105,397 Reputation
184 Guides authored
Badges:
46
+43 more badges
Team
iFixit
Member of iFixit
Community
141 Members
15,769 Guides authored
Kerem - Dec 9, 2019
Reply
Hallo,
habe den Akku (30€ über eBay
Alexander - May 3, 2021
Reply
Hi kann mir einer sagen ob der Akku denn man im ifixit Shop kaufen kann ein ni-mh Akku ist?
Tobias Isakeit - May 19, 2021
Jep, es handelt sich um einen NiMH Akku (ist auf dem Produktbild zu sehen). Wie der originale, und sogar mit etwas mehr Ladung ;)
yvi14 - May 27, 2021
Reply
Und ist es besser einen mit mehr Ladung zu nehmen oder sollte man es so wie im Original nutzen? Was ist in dem Original Akku der Tonie Box? 1800mAh?
Tobias Isakeit - Jul 7, 2021
Der originale hat 2000 mAh, der in unserem Store hat 2200 mAh. Hält einfach ein wenig länger ;)