Difficulty
Easy
Steps
7
Time Required
10 - 20 minutes
Sections
2
- Back Panel
- 4 steps
- Screen
- 3 steps
Flags
1
Incorrect Tools
Help make this guide better by using the correct tools in images and/or text.
BackTomTom One XL
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Back Panel
- Remove the 4 .4mm screws on the back of the device.
Remove the 4 .4mm screws on the back of the device.
1024
Step 2
- Using the palate knife tool, pry the back from the LCD screen. Apply a moderate pressure to separate them.
- You can rotate TOMTOM XL to make prying back off easier.
- Be careful not to injure the two wires connecting the pieces.
Using the palate knife tool, pry the back from the LCD screen. Apply a moderate pressure to separate them.
You can rotate TOMTOM XL to make prying back off easier.
Be careful not to injure the two wires connecting the pieces.
Step 3
- After prying both halves apart, they will be connected by two wires.
- Carefully set the two halves next to each other making sure not to stress or damage the wires.
After prying both halves apart, they will be connected by two wires.
Carefully set the two halves next to each other making sure not to stress or damage the wires.
Step 4
- Using the tweezers separate the wires connecting the battery and speaker to the mother board.
- Be gentle while pulling the wires out, the plugs are easily injured.
Using the tweezers separate the wires connecting the battery and speaker to the mother board.
Be gentle while pulling the wires out, the plugs are easily injured.
Step 5
Screen
- Locate the 4 .4mm screws connecting the circuit board to the front panel.
- Use the T6 Torx screwdriver and remove the four screws.
Locate the 4 .4mm screws connecting the circuit board to the front panel.
Use the T6 Torx screwdriver and remove the four screws.
Step 6
- Locate the ribbon cable connecting the front panel to the circuit board.
- Locate the white tab locking the ribbon in place.
- Using precision tweezers push the left and right side of the tab forward.
- Gently pull the ribbon to disconnect the circuit board from the front panel.
- If gently pulling on the ribbon doesn’t release it then the tab hasn’t been pushed far enough forward.
Locate the ribbon cable connecting the front panel to the circuit board.
Locate the white tab locking the ribbon in place.
Using precision tweezers push the left and right side of the tab forward.
Gently pull the ribbon to disconnect the circuit board from the front panel.
If gently pulling on the ribbon doesn’t release it then the tab hasn’t been pushed far enough forward.
Step 7
- Use the palate knife to pry the screen away from the front panel.
- Pry between the light gray board and the black boarder of the TOMTOM XL screen.
- Use moderate pressure when prying, slide the palate knife back and forth, and eventually the screen should pop out.
Use the palate knife to pry the screen away from the front panel.
Pry between the light gray board and the black boarder of the TOMTOM XL screen.
Use moderate pressure when prying, slide the palate knife back and forth, and eventually the screen should pop out.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
Author
with 2 other contributors
DeVhan
Member since: 03/11/2015
401 Reputation
4 Guides authored
Badges:
4
+1 more badge
Team
Colorado Springs, Team 9-6, Panko Spring 2015
Member of Colorado Springs, Team 9-6, Panko Spring 2015
UCCS-PANKO-S15S9G6
3 Members
5 Guides authored
