Difficulty

Moderate

Steps

7

Time Required

                          10 - 15 minutes            

Sections

6

  • Tank Lid
  • 1 step
  • Shutting off the Water Supply to a Toilet
  • 1 step
  • Draining a Toilet Tank
  • 1 step
  • Sponge Drying a Toilet Tank
  • 1 step
  • Supply Tube
  • 1 step
  • Tank Assembly
  • 2 steps

Flags

0

  • BackToilet

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

What you need

Step 1

              Tank Lid               
  • Lift the tank lid up and away from the toilet tank.

Lift the tank lid up and away from the toilet tank.

1024

Step 2

              Shutting off the Water Supply to a Toilet               
  • Shut off the stop valve underneath the toilet by turning it clockwise until it becomes hand tight.
  • The appearance of this valve may differ from toilet to toilet, but most operate the same. Some valves require multiple turns to stop the water while others only require a quarter turn.

Shut off the stop valve underneath the toilet by turning it clockwise until it becomes hand tight.

The appearance of this valve may differ from toilet to toilet, but most operate the same. Some valves require multiple turns to stop the water while others only require a quarter turn.

Step 3

              Draining a Toilet Tank               
  • Push down the flush lever.
  • Hold the lever down until water stops draining from the tank.
  • A small amount of water will remain in the bottom of the tank.
  • If the flush lever or pull chain have become disconnected, lift up the toilet flapper to drain the tank.

Push down the flush lever.

Hold the lever down until water stops draining from the tank.

A small amount of water will remain in the bottom of the tank.

If the flush lever or pull chain have become disconnected, lift up the toilet flapper to drain the tank.

Step 4

              Sponge Drying a Toilet Tank               
  • Use a sponge to soak up and remove any remaining water from the toilet tank.
  • Periodically squeeze the excess water from the sponge.

Use a sponge to soak up and remove any remaining water from the toilet tank.

Periodically squeeze the excess water from the sponge.

Step 5

              Supply Tube               
  • Place a bucket under the supply tube to catch any dripping water.
  • Turn the coupling nut on the supply tube clockwise until it releases from the threaded shank on the bottom of the tank.

Place a bucket under the supply tube to catch any dripping water.

Turn the coupling nut on the supply tube clockwise until it releases from the threaded shank on the bottom of the tank.

Step 6

              Tank Assembly               
  • Using a socket wrench to hold the nuts, unscrew the two tank bolts with a screwdriver.
  • When reattaching the tank, tighten the bolts with a screwdriver, rather than tightening the nuts. Alternately tighten each bolt in increments, until the tank fits snugly against the toilet.
  • Avoid over-tightening the tank bolts. Too much force can easily crack the toilet tank or toilet bowl.

Using a socket wrench to hold the nuts, unscrew the two tank bolts with a screwdriver.

When reattaching the tank, tighten the bolts with a screwdriver, rather than tightening the nuts. Alternately tighten each bolt in increments, until the tank fits snugly against the toilet.

Avoid over-tightening the tank bolts. Too much force can easily crack the toilet tank or toilet bowl.

Step 7

  • Lift the tank up from the lower half of the toilet.
  • Set the tank on a thick towel to avoid scraping it against the floor.

Lift the tank up from the lower half of the toilet.

Set the tank on a thick towel to avoid scraping it against the floor.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      10 other people completed this guide.                                             

Author

                                      with 1 other contributor 

                    Ron Davis                     

Member since: 02/17/2015

29,609 Reputation

                                      13 Guides authored                  



                       Badges:
                       40







                                                        +37 more badges                           

John Pretz - Jun 13, 2016

Reply

Step 5: Clockwise or counter-clockwise depends upon whether you are looking down at the coupling nut from above or up at it from below.

I suspect that, unless it has a left-handed thread, most people would turn it in the direction that works.

M J McAllister - Jul 15, 2016

Reply

Close your eyes. Attaching something, the turning motion is (usually) clockwise: Righty-tighty; lefty-loosey.

DonnaRHellman - Oct 10, 2018

Reply

Thank you for the info.