Difficulty

Moderate

Steps

15

Time Required

                          15 - 20 minutes            

Sections

3

  • Rear Case
  • 6 steps
  • Battery
  • 4 steps
  • Speaker
  • 5 steps

Flags

1

Needs Better Images

Better photos will improve this guide. Help out by taking, editing, or uploading new ones!

  • BackTivax MiTraveler 10Q-8

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

What you need

Step 1

              Rear Case               
  • With the device face down, slide the charging port cover off on the left side of device.

With the device face down, slide the charging port cover off on the left side of device.

1024

Step 2

  • A phillips 2.88mm screw will be seen at the charging port.

A phillips 2.88mm screw will be seen at the charging port.

Step 3

  • Use a PH000 Philips head screwdriver to remove screw.
  • Remember lefty loosey, righty tighty

Use a PH000 Philips head screwdriver to remove screw.

Remember lefty loosey, righty tighty

Step 4

  • Use the plastic opening tool between the back plate and front plate to pry the back plate off; start at the headphone jack.
  • Make sure the lip of the plastic opening tool is face up.

Use the plastic opening tool between the back plate and front plate to pry the back plate off; start at the headphone jack.

Make sure the lip of the plastic opening tool is face up.

Step 5

  • Move around the device with the plastic opening tool pushing down to release the back plate from clips.
  • You will hear popping sounds when you work around the device.

Move around the device with the plastic opening tool pushing down to release the back plate from clips.

You will hear popping sounds when you work around the device.

Step 6

  • Once you’ve moved around the whole device with the plastic opening tool, the back plate will completely release from the rest of the device.

Once you’ve moved around the whole device with the plastic opening tool, the back plate will completely release from the rest of the device.

Step 7

              Battery               
  • The battery rests flat on the inside surface of the tablet. It is a rectangular shape and has blue and yellow tape.

The battery rests flat on the inside surface of the tablet. It is a rectangular shape and has blue and yellow tape.

Step 8

  • There are two wires, one red and one black, that need to be desoldered from the motherboard that run to the battery.
  • Review how to solder here.

There are two wires, one red and one black, that need to be desoldered from the motherboard that run to the battery.

Review how to solder here.

Step 9

  • Work the soldering gun on the red wire where it is connected to the motherboard. it should release from the motherboard.
  • Work the soldering gun on the black wire where it is connected to the motherboard. It will release from the motherboard.

Work the soldering gun on the red wire where it is connected to the motherboard. it should release from the motherboard.

Work the soldering gun on the black wire where it is connected to the motherboard. It will release from the motherboard.

Step 10

  • Once both wires have been desoldered, the battery can be removed from the device.

Once both wires have been desoldered, the battery can be removed from the device.

Step 11

              Speaker               
  • With the face of the device down, the speaker will be in the upper right corner. The black oval shaped object.
  • Make sure Battery has been removed.

With the face of the device down, the speaker will be in the upper right corner. The black oval shaped object.

Make sure Battery has been removed.

Step 12

  • A phillips 3.88 mm screw will be holding the speaker in place.
  • Use a PH000 screwdriver to remove the screw.

A phillips 3.88 mm screw will be holding the speaker in place.

Use a PH000 screwdriver to remove the screw.

Step 13

  • The speaker will be connected to two wires; one black and one red. Both run to the motherboard.
  • The wires will need to be soldered off the motherboard.
  • Locate where both wires are soldered to the motherboard.
  • Review How to Solder Here

The speaker will be connected to two wires; one black and one red. Both run to the motherboard.

The wires will need to be soldered off the motherboard.

Locate where both wires are soldered to the motherboard.

Review How to Solder Here

Step 14

  • Work the iron where the red wire is soldered
  • The wire will release from the motherboard.

Work the iron where the red wire is soldered

The wire will release from the motherboard.

Step 15

  • Work the iron where the black wire is soldered.
  • The black wire will release from the motherboard.
  • After both wires have been soldered off, the speaker will release from the device.

Work the iron where the black wire is soldered.

The black wire will release from the motherboard.

After both wires have been soldered off, the speaker will release from the device.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

Author

                                      with 3 other contributors 

                    Krista                     

Member since: 03/11/2015

131 Reputation

                                      1 Guide authored                  



                       Badges:
                       7







                                                        +4 more badges                           

Team

                       Colorado Springs, Team 4-3, Panko Spring 2015                        

                                                  Member of Colorado Springs, Team 4-3, Panko Spring 2015 



                    UCCS-PANKO-S15S4G3                     


                                            3 Members                     


                                            10 Guides authored