Ti 84 Plus Silver Edition Keyboard Mat Replacement Repair Guide

Difficulty

Moderate

Steps

Time Required

                          10 - 20 minutes

Sections

Faceplate
2 steps
Main Battery
2 steps
Backup Battery
3 steps
Motherboard and Screen
4 steps
Keyboard Mat
1 step

Flags

BackTexas Instruments TI-84 Plus Silver Edition
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications

Introduction

What you need

Step 1

              Faceplate

Insert your index finger in the open slot below the keys.
Be careful to not bend the plate too much because it is very thin and might break.
Apply a firm upward force until the bottom two tabs located near the bottom of the plate come off.

Insert your index finger in the open slot below the keys.

Be careful to not bend the plate too much because it is very thin and might break.

Apply a firm upward force until the bottom two tabs located near the bottom of the plate come off.

1024

Step 2

Grab the face plate on each side near the middle and apply a gentle upward force on each side until the middle tabs come off.
A tab is located in the center of the face plate. If it is still attached, then continue to apply a gentle upward force until the center tab comes off.
Lift the face plate upward until the top three tabs come off and the face plate is completely detached.

Grab the face plate on each side near the middle and apply a gentle upward force on each side until the middle tabs come off.

A tab is located in the center of the face plate. If it is still attached, then continue to apply a gentle upward force until the center tab comes off.

Lift the face plate upward until the top three tabs come off and the face plate is completely detached.

Step 3

              Main Battery

Push firmly down on the tab located on the back of the calculator near the center.
Pull the tab up, lifting it off of the calculator and exposing the batteries.

Push firmly down on the tab located on the back of the calculator near the center.

Pull the tab up, lifting it off of the calculator and exposing the batteries.

Step 4

Removing the AAAs and the back up battery will clear the calculator’s memory. Make sure you have backed up any important data prior to performing this step.
Push the positive (+) side of the batteries to remove them

Removing the AAAs and the back up battery will clear the calculator’s memory. Make sure you have backed up any important data prior to performing this step.

Push the positive (+) side of the batteries to remove them

Step 5

              Backup Battery

Using the Phillips #00 Screwdriver, unscrew the 15 mm screw holding the backup battery cover, located above the main battery area.

Using the Phillips #00 Screwdriver, unscrew the 15 mm screw holding the backup battery cover, located above the main battery area.

Step 6

Grab the plate and lift gently upward, to remove the backup battery cover.

Grab the plate and lift gently upward, to remove the backup battery cover.

Step 7

Wedge the small plastic opening tool under the backup battery in the gap to the left of the backup battery.
The backup battery is an SR44SW coin cell battery. You can also replace it with a size 357/303 or LR44 battery.
Push gently downward until the backup battery pops out.

Wedge the small plastic opening tool under the backup battery in the gap to the left of the backup battery.

The backup battery is an SR44SW coin cell battery. You can also replace it with a size 357/303 or LR44 battery.

Push gently downward until the backup battery pops out.

Step 8

              Motherboard and Screen

Unscrew the six 8.5 mm screws located on the perimeter of the back cover using the Precision T6 Torx Screwdriver.

Unscrew the six 8.5 mm screws located on the perimeter of the back cover using the Precision T6 Torx Screwdriver.

Step 9

Wedge the large plastic opening tool in the gap at the bottom between the top and bottom covers.
Apply a gentle downward force to separate the top cover from the bottom cover.
Wedge the large plastic opening tool in the gaps along each side to unhook the side clips.
There are clips located at the bottom of the calculator, on the sides of the calculator (both near the bottom and near the top), and at the top of the calculator.
Pull the bottom cover apart from the top cover.

Wedge the large plastic opening tool in the gap at the bottom between the top and bottom covers.

Apply a gentle downward force to separate the top cover from the bottom cover.

Wedge the large plastic opening tool in the gaps along each side to unhook the side clips.

There are clips located at the bottom of the calculator, on the sides of the calculator (both near the bottom and near the top), and at the top of the calculator.

Pull the bottom cover apart from the top cover.

Step 10

Unscrew the two 5 mm screws at the bottom of the silver sheet using the Phillips #00 Screwdriver.
Pull up on the silver sheet from the top to remove it from the calculator.

Unscrew the two 5 mm screws at the bottom of the silver sheet using the Phillips #00 Screwdriver.

Pull up on the silver sheet from the top to remove it from the calculator.

Step 11

Unscrew the four 5 mm screws on the sides of the mother board Phillips #00 Screwdriver.
Pry the motherboard out from the bottom of the front casing using the large plastic opening tool.

Unscrew the four 5 mm screws on the sides of the mother board Phillips #00 Screwdriver.

Pry the motherboard out from the bottom of the front casing using the large plastic opening tool.

Step 12

              Keyboard Mat

Flip over the motherboard to reveal the keys
Carefully peal the mat from the motherboard.
Do not invert the mat as the keys may fall off.

Flip over the motherboard to reveal the keys

Carefully peal the mat from the motherboard.

Do not invert the mat as the keys may fall off.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      3 other people completed this guide.

Author

                                      with 5 other contributors

                    Kale McKinney

Member since: 10/20/2013

855 Reputation

                                      3 Guides authored                  



                       Badges:
                       11







                                                        +8 more badges

Team

                       Cal Poly, Team 11-34, Amido Fall 2013                        

                                                  Member of Cal Poly, Team 11-34, Amido Fall 2013 



                    CPSU-AMIDO-F13S11G34                     


                                            4 Members                     


                                            6 Guides authored

Introduction#

What you need#

Team#

Introduction

What you need

Team