Difficulty

Moderate

Steps

4

Time Required

                          30 minutes            

Sections

2

  • Keyboard
  • 3 steps
  • Keyboard
  • 1 step

Flags

0

  • BackTeenage Engineering OP-1

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

This guide shows you how to replace the keyboard of your OP-1.

What you need

Step 1

              key removal               
  • To get to the screws beneath the keyboard you need to take some keys off. You can use either an opening tool or an opening pick. The first picture shows how it should look like with all the necessary keys off (12 in total).
  • The four longer keys from the fingerboard are to be handled from the left side to get them off.
  • The eight smaller keys need to be levered from the bottom up.

To get to the screws beneath the keyboard you need to take some keys off. You can use either an opening tool or an opening pick. The first picture shows how it should look like with all the necessary keys off (12 in total).

The four longer keys from the fingerboard are to be handled from the left side to get them off.

The eight smaller keys need to be levered from the bottom up.

1024

Step 2

              removing scissors mechanisms               
  • The scissor mechanism of the eight small keys are obstructing the underlying screws.
  • By using again an opening tool or opening pick these can be snapped off easily.
  • When reassembling be sure to place them in with the correct side facing upwards.

The scissor mechanism of the eight small keys are obstructing the underlying screws.

By using again an opening tool or opening pick these can be snapped off easily.

When reassembling be sure to place them in with the correct side facing upwards.

Step 3

              unscrew keyboard               
  • Loosen those 12 screws with a Phillips #00 screwdriver.
  • Then just pull off the four rotary knobs and the volume knob.
  • Now it is possible to slightly lift the keyboard and set it back.

Loosen those 12 screws with a Phillips #00 screwdriver.

Then just pull off the four rotary knobs and the volume knob.

Now it is possible to slightly lift the keyboard and set it back.

Step 4

              Keyboard Connection               
  • Unlock the flex cables by pushing the two black nibs on both sides of each connector.
  • Now you can pull the flex cables out and remove the keyboard completely.
  • When installing the new keyboard, make sure to remove the protective film underneath the screen.
  • The OP-1 has a mode to test specific functions. You can enter it by holding the “COM” button while powering on, then choose the function test (2). You don’t have to complete every test and can power off after the keyboard test.

Unlock the flex cables by pushing the two black nibs on both sides of each connector.

Now you can pull the flex cables out and remove the keyboard completely.

When installing the new keyboard, make sure to remove the protective film underneath the screen.

The OP-1 has a mode to test specific functions. You can enter it by holding the “COM” button while powering on, then choose the function test (2). You don’t have to complete every test and can power off after the keyboard test.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      19 other people completed this guide.                                             

Author

                    Tobias Isakeit                     

Member since: 03/31/2014

105,397 Reputation

                                      184 Guides authored                  



                       Badges:
                       46







                                                        +43 more badges                           

Team

                       iFixit                        

                                                  Member of iFixit 



                    Community                     


                                            141 Members                     


                                            15,767 Guides authored                     

Flavius Ivancu - Aug 8, 2016

Reply

Nice guide Tobias!

Worked like a charm. My OP-1 feels brand new.

Thanks iFixit X TeenageEngineering for providing these replacement parts!

Keep it up <3

Jason Wasiak - Sep 23, 2016

Reply

Awesome guide! Thank you!!!

Raimund S - Oct 24, 2016

Reply

After reassembling everything I have one key ( the upper A) which retriggers the sound randomly if I press the key.

I hope that the reason is not that I put the flex cable back too loose … and i have to open it again. Anyone had this before?

Qaiyyum Tajudin - Sep 5, 2019

This happened to me constantly, only by taking the key off I noticed the tiniest amount of moisture, a mere misting, nesting in the board. it had been re-triggering randomly… Not ideal whilst constantly gigging. Seems to be triggering normally now after drying it in front of a heater. The only thing I think could of caused this is a dry ice machine I played beside a few weeks ago.

kristianottosen - Dec 25, 2016

Reply

Perfect. Thanks :)