Difficulty
Moderate
Steps
5
Time Required
30 minutes
Sections
3
- Connector Board Connection
- 1 step
- Keyboard
- 3 steps
- Battery
- 1 step
Flags
0
BackTeenage Engineering OP-1
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
In this case it’s a 1800 mAh li-polymer battery at 3.7V (that is 6660 mWh).
What you need
Step 1
Remove Back Panel
- Open the back panel by using a Jimmy on the side of the panel. Be careful not to damage the OP-1 coating.
- Lift the back panel and remove it. The Connector Board is revealed.
- Disconnect the flex connector by lifting it up with a spudger.
Open the back panel by using a Jimmy on the side of the panel. Be careful not to damage the OP-1 coating.
Lift the back panel and remove it. The Connector Board is revealed.
Disconnect the flex connector by lifting it up with a spudger.
1024
Step 2
key removal
- To get to the screws beneath the keyboard you need to take some keys off. You can use either an opening tool or an opening pick. The first picture shows how it should look like with all the necessary keys off (12 in total).
- The four longer keys from the fingerboard are to be handled from the left side to get them off.
- The eight smaller keys need to be levered from the bottom up.
To get to the screws beneath the keyboard you need to take some keys off. You can use either an opening tool or an opening pick. The first picture shows how it should look like with all the necessary keys off (12 in total).
The four longer keys from the fingerboard are to be handled from the left side to get them off.
The eight smaller keys need to be levered from the bottom up.
Step 3
removing scissors mechanisms
- The scissor mechanism of the eight small keys are obstructing the underlying screws.
- By using again an opening tool or opening pick these can be snapped off easily.
- When reassembling be sure to place them in with the correct side facing upwards.
The scissor mechanism of the eight small keys are obstructing the underlying screws.
By using again an opening tool or opening pick these can be snapped off easily.
When reassembling be sure to place them in with the correct side facing upwards.
Step 4
unscrew keyboard
- Loosen those 12 screws with a Phillips #00 screwdriver.
- Then just pull off the four rotary knobs and the volume knob.
- Now it is possible to slightly lift the keyboard and set it back.
Loosen those 12 screws with a Phillips #00 screwdriver.
Then just pull off the four rotary knobs and the volume knob.
Now it is possible to slightly lift the keyboard and set it back.
Step 5
battery removal
- Carefully pull out the connector cable from the connector board and bend it out of the way.
- Disconnect the battery with a spudger. The connector needs to be lifted up and not being pulled to the side.
- Now you can pry out the battery which is glued in with double sided adhesive tape.
Carefully pull out the connector cable from the connector board and bend it out of the way.
Disconnect the battery with a spudger. The connector needs to be lifted up and not being pulled to the side.
Now you can pry out the battery which is glued in with double sided adhesive tape.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
10 other people completed this guide.
Author
with 2 other contributors
Tobias Isakeit
Member since: 03/31/2014
105,397 Reputation
184 Guides authored
Badges:
46
+43 more badges
Team
iFixit
Member of iFixit
Community
141 Members
15,767 Guides authored
TrustNoShadows - Sep 5, 2016
Reply
This is great. What type of battery is the replacement?? thanks!
Tobias Isakeit - Sep 6, 2016
Hi, thanks for the question. I added another picture and put some information in the introduction.
lfsaw - Sep 11, 2016
Reply
hey, thanks for this! is the battery plug simple JST or do I need to get something specific?
Tobias Isakeit - Sep 12, 2016
Yes, a simple JST plug (probably type ACH)
Clarke Robinson - Sep 16, 2016
Reply
Thanks for posting these instructions! I’m having trouble finding a battery that matches the one in the picture (unless I want to buy 1000 of them from Alibaba). Would this work?
http://www.ebay.com/itm/3-7V-1800mAh-Rec…
Dimensions are:
thick:3mm
wide:60mm
length:70mm