Difficulty
Difficult
Steps
13
Time Required
1 hour
Sections
4
- Battery
- 3 steps
- Arms
- 6 steps
- Housing Cover
- 1 step
- Eyes
- 3 steps
Flags
1
Featured Student Guide
This guide has been the hard work of our awesome students and is found to be exceptionally cool by the iFixit staff.
BackTeddy Ruxpin
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Battery
- Remove the vest covering the back of the bear.
- Orient the bear with his back facing upwards and unscrew the single Phillips #2 screw.
- Captured screws will stay in place, no need to worry about losing this one!
Remove the vest covering the back of the bear.
Orient the bear with his back facing upwards and unscrew the single Phillips #2 screw.
Captured screws will stay in place, no need to worry about losing this one!
1024
Step 2
- Pull the tab outward to remove the protective plate for the batteries.
Pull the tab outward to remove the protective plate for the batteries.
Step 3
- Remove all four AA batteries by pushing the positive end down and pulling the battery out toward yourself.
Remove all four AA batteries by pushing the positive end down and pulling the battery out toward yourself.
Step 4
Arms
- Cut the orange shirt and zip tie.
- Remove the zip tie.
Cut the orange shirt and zip tie.
Remove the zip tie.
Step 5
- Cut across the back seam of the head of the bear along the arrow.
- This damages the bear’s exterior and will require resewing.
Cut across the back seam of the head of the bear along the arrow.
This damages the bear’s exterior and will require resewing.
Step 6
- Remove the interior of the doll.
- Peel the outer layer around the head of the bear and forcefully pry off the face of the bear from the outside layer of the bear.
- This will be difficult and require significant force, but do not fear about breaking the doll at this stage.
Remove the interior of the doll.
Peel the outer layer around the head of the bear and forcefully pry off the face of the bear from the outside layer of the bear.
This will be difficult and require significant force, but do not fear about breaking the doll at this stage.
Step 7
- Extract each arm button.
- Pull on the stuffing of the bear and not the wire to remove the arm button.
Extract each arm button.
Pull on the stuffing of the bear and not the wire to remove the arm button.
Step 8
- Pull off the rest of the outside layer of the bear.
Pull off the rest of the outside layer of the bear.
Step 9
- Unplug the arms from the main body.
Unplug the arms from the main body.
Step 10
Housing Cover
- Unscrew the eleven circled 12.5mm Phillips #1 screws.
- Remove the top of the housing to access the electronics inside.
Unscrew the eleven circled 12.5mm Phillips #1 screws.
Remove the top of the housing to access the electronics inside.
Step 11
Eyes
- Using a Phillips #1 screwdriver, remove the two 12.5mm screws connecting the eyes to the rest of the mechanism.
Using a Phillips #1 screwdriver, remove the two 12.5mm screws connecting the eyes to the rest of the mechanism.
Step 12
- Unplug the two sets of wires connected to the back of the eyes by using moderate to high force.
Unplug the two sets of wires connected to the back of the eyes by using moderate to high force.
Step 13
- Once those wires are disconnected, desolder the wires connected from the eye motherboard.
Once those wires are disconnected, desolder the wires connected from the eye motherboard.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
One other person completed this guide.
Author
with 4 other contributors
Jayin Patel
Member since: 01/23/2020
382 Reputation
4 Guides authored
Badges:
7
+4 more badges
Team
Cal Poly, Team S18-G5, White Winter 2020
Member of Cal Poly, Team S18-G5, White Winter 2020
CPSU-WHITE-W20S18G5
4 Members
7 Guides authored
