Difficulty
Moderate
Steps
14
Time Required
30 minutes - 1 hour
Sections
4
- Disassembling TDK Life on Record bottom panel
- 6 steps
- Air Vent Tube
- 2 steps
- Motherboard
- 4 steps
- Handle
- 2 steps
Flags
2
Grammar Police
Embrace your inner English teacher and help improve this guide’s grammar!
Missed a Step
Oops! This guide is currently missing some important steps.
BackTDK Life on Record Trek 360
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
What you need
Step 1
Disassembling TDK Life on Record bottom panel
- Remove the four rubber feet of the device using a metal spudger.
Remove the four rubber feet of the device using a metal spudger.
1024
Step 2
- Remove the four 9 mm Phillips #0 screws located under the feet of the device.
- Remove the four 9 mm Torx #8 screws located on each side of the bottom the device.
Remove the four 9 mm Phillips #0 screws located under the feet of the device.
Remove the four 9 mm Torx #8 screws located on each side of the bottom the device.
Step 3
- Pull the bottom cover of the device towards you.
Pull the bottom cover of the device towards you.
Step 4
- Remove the four 13 mm Phillips #1 screws.
Remove the four 13 mm Phillips #1 screws.
Step 5
- Use one hand to grip the device from the side of the handle, and use the other hand to grip the side of the device that contains the woofer
- The woofer is the circular component located at the bottom of the device after the bottom cover has been removed
- Pull apart the compartments by applying force in opposite directions.
- Do not pull with extreme force!! There are many electrical wires inside the device that can become damaged if the bottom panel is removed without care
Use one hand to grip the device from the side of the handle, and use the other hand to grip the side of the device that contains the woofer
The woofer is the circular component located at the bottom of the device after the bottom cover has been removed
Pull apart the compartments by applying force in opposite directions.
Do not pull with extreme force!! There are many electrical wires inside the device that can become damaged if the bottom panel is removed without care
Step 6
- Disconnect the seven cables attached to the motherboard.
- Do not use too much force when pulling on the wires. Pulling with too much force can damage the wires.
Disconnect the seven cables attached to the motherboard.
Do not use too much force when pulling on the wires. Pulling with too much force can damage the wires.
Step 7
Air Vent Tube
- Remove the four 8 mm Phillips #1 screws.
Remove the four 8 mm Phillips #1 screws.
Step 8
- place your hands on each side of the air vent and then place your index finger on the thin plastic half circle that holds the vent in place.
- Pull the plastic half circle towards you.
- Put both of your hands inside the tube as shown and push away from you.
place your hands on each side of the air vent and then place your index finger on the thin plastic half circle that holds the vent in place.
Pull the plastic half circle towards you.
Put both of your hands inside the tube as shown and push away from you.
Step 9
Motherboard
- Remove the four wired clips by pulling on the wires.
- Remove the three 6 mm Phillips #1 screws.
Remove the four wired clips by pulling on the wires.
Remove the three 6 mm Phillips #1 screws.
Step 10
- Remove the volume control knob, which is located at the front of the speaker, by pulling it towards you.
Remove the volume control knob, which is located at the front of the speaker, by pulling it towards you.
Step 11
- Using tweezers, turn the nut counter-clockwise and remove the nut.
Using tweezers, turn the nut counter-clockwise and remove the nut.
Step 12
- Push the metal part that holds the volume control knob away from you.
Push the metal part that holds the volume control knob away from you.
Step 13
Handle
Step 14
- Use your left hand to hold the top portion of the speaker in place.
- Using your right hand, pull the handle away from the device.
Use your left hand to hold the top portion of the speaker in place.
Using your right hand, pull the handle away from the device.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
Author
with 2 other contributors
Eduardo Barrios
Member since: 09/14/2015
323 Reputation
2 Guides authored
Badges:
9
+6 more badges
Team
CSU Fullerton, Team 1-2, Bruce Fall 2015
Member of CSU Fullerton, Team 1-2, Bruce Fall 2015
CSUF-BRUCE-F15S1G2
3 Members
5 Guides authored