Tapwave T2907Us Zodiac 2 Touchscreen Display Replacement Repair Guide

Difficulty

Moderate

Steps

14

Time Required

                          20 - 30 minutes            

Sections

4

• Back Cover
• 2 steps
• Battery
• 2 steps
• Motherboard
• 7 steps
• Touchscreen/Display
• 3 steps

Flags

3

Confusing Text

Some of this guide’s text is confusing, duplicated, or off-topic. Clarify it by editing!

Needs More Images

A few more images would make this guide’s procedures crystal clear.

Action Shots

Be an action hero! This guide needs images that better demonstrate how to perform specific actions.

• BackTapwave T2907US Zodiac 2

• Full Screen

• Options

• History

• Save to Favorites

• Download PDF

• Edit

• Translate

• Get Shareable Link

• Embed This Guide

• Notify Me of Changes

• Stop Notifications

Introduction

What you need

Step 1

              Back Cover               

• Remove the four Torx T5 screws from the back panel.

Remove the four Torx T5 screws from the back panel.

1024

Step 2

• Wedge a spudger in between the front and back panel.
• Apply leverage downwards to the spudger in order to remove the back panel.

Wedge a spudger in between the front and back panel.

Apply leverage downwards to the spudger in order to remove the back panel.

Step 3

              Battery               

• Slide the battery out from under the brown wire-tape.
• Be careful of the wires still connected to the other end of the battery. Do not pull or damage may occur.

Slide the battery out from under the brown wire-tape.

Be careful of the wires still connected to the other end of the battery. Do not pull or damage may occur.

Step 4

• Slowly pull the white plug from its receptor. Grasp its sides firmly with a pair of tweezers and gently wiggle from side to side.

Slowly pull the white plug from its receptor. Grasp its sides firmly with a pair of tweezers and gently wiggle from side to side.

Step 5

              Motherboard               

• Unscrew the 2 Philips #00 screws on each end of the motherboard.

Unscrew the 2 Philips #00 screws on each end of the motherboard.

Step 6

• Pull off the black memory card slot piece with tweezers.

Pull off the black memory card slot piece with tweezers.

Step 7

• Unscrew the 2 Philips #00 screws on each side of the charging port.

Unscrew the 2 Philips #00 screws on each side of the charging port.

Step 8

• Disconnect 2 brown wire-tape ends from each end of the motherboard. Gently pull straight out with tweezers.

Disconnect 2 brown wire-tape ends from each end of the motherboard. Gently pull straight out with tweezers.

Step 9

• Pull the motherboard and screen component diagonally up and left away from the auxiliary port entrance to remove.
• Glue connecting the auxiliary port to the casing may make it difficult to remove. Gently apply force as needed.

Pull the motherboard and screen component diagonally up and left away from the auxiliary port entrance to remove.

Glue connecting the auxiliary port to the casing may make it difficult to remove. Gently apply force as needed.

Step 10

• Disconnect the 2 brown wire-tape ends from the left side of the battery slot on the motherboard using tweezers.

Disconnect the 2 brown wire-tape ends from the left side of the battery slot on the motherboard using tweezers.

Step 11

• Disconnect the large brown wire-tape from the motherboard.
• Peel the black tape back from the wire-tape using tweezers.
• Lift the black, hinged, plastic lock with tweezers to release the wire-tape.
• The screen and motherboard components can now be separated from each other.

Disconnect the large brown wire-tape from the motherboard.

Peel the black tape back from the wire-tape using tweezers.

Lift the black, hinged, plastic lock with tweezers to release the wire-tape.

The screen and motherboard components can now be separated from each other.

Step 12

              Touchscreen/Display               

• Unscrew the 2 Philips #00 screws from the bottom edge of the screen component.

Unscrew the 2 Philips #00 screws from the bottom edge of the screen component.

Step 13

• Take off the brown wire-tape from the small circuit board component.
• Lift up so that the black plastic hinge piece swings open and the tape can be removed.

Take off the brown wire-tape from the small circuit board component.

Lift up so that the black plastic hinge piece swings open and the tape can be removed.

Step 14

• Warning: If you are too rough with the screwdriver, you can permanently damage the display.
• Use a Slot SL1.5 screwdriver to pry the touchscreen shell from the display component using the 4 slots around the entire component

Warning: If you are too rough with the screwdriver, you can permanently damage the display.

Use a Slot SL1.5 screwdriver to pry the touchscreen shell from the display component using the 4 slots around the entire component

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

Author

                                      with 5 other contributors 

                    Daniel Wiseman                     

Member since: 01/20/2012

133 Reputation

                                      6 Guides authored                  



                       Badges:
                       9







                                                        +6 more badges                           

Team

                       Cal Poly, Team 10-33, Amido Winter 2012                        

                                                  Member of Cal Poly, Team 10-33, Amido Winter 2012 



                    CPSU-AMIDO-W12S10G33                     


                                            4 Members                     


                                            10 Guides authored