T Mobile Sda Htc Tornado Keypad Replacement Repair Guide

Difficulty

Moderate

Steps

Time Required

                          1 hour

Sections

Battery
2 steps
Rear Phone Casing
3 steps
Circuit Board
1 step
Keypad
3 steps

Flags

BackT-Mobile SDA (HTC Tornado)
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications

Introduction

What you need

Step 1

              Battery

To remove the battery cover, first turn the phone so that the keypad is face down.
While holding the phone with one hand, place the thumb of the other hand at the top of the battery cover.
Slide the battery cover toward the bottom of the phone to remove.

To remove the battery cover, first turn the phone so that the keypad is face down.

While holding the phone with one hand, place the thumb of the other hand at the top of the battery cover.

Slide the battery cover toward the bottom of the phone to remove.

1024

Step 2

To remove the battery, first grab it using a finger on either side.
Pull the battery upward, while securing the phone with your other hand.
Gently remove the battery and place it to the side of the phone.

To remove the battery, first grab it using a finger on either side.

Pull the battery upward, while securing the phone with your other hand.

Gently remove the battery and place it to the side of the phone.

Step 3

              Rear Phone Casing

Move the battery and battery cover to the side and pick up the phone.
Use the plastic opening tool to remove the camera casing located at the top of the phone.
Use your fingers to pull out the gray antenna casing.

Move the battery and battery cover to the side and pick up the phone.

Use the plastic opening tool to remove the camera casing located at the top of the phone.

Use your fingers to pull out the gray antenna casing.

Step 4

Hold the phone with one hand and the plastic opening tool with the other.
Pry the outer casing off of the phone by wedging the plastic opening tool between the casing and the phone, thus dislocating the tabs.
Place the outer casing to the side.

Hold the phone with one hand and the plastic opening tool with the other.

Pry the outer casing off of the phone by wedging the plastic opening tool between the casing and the phone, thus dislocating the tabs.

Place the outer casing to the side.

Step 5

Using the T5 or T6 screwdriver, remove the six screws from the back of the phone, as shown in the first image.
Remove the back half of the phone by using the plastic opening tool to pry apart the top half from the bottom half. Wedge the plastic opening tool tool around the edge of the phone to dislocate the tabs.
Once the tabs are dislocated, pull the back of the phone apart from the front half.

Using the T5 or T6 screwdriver, remove the six screws from the back of the phone, as shown in the first image.

Remove the back half of the phone by using the plastic opening tool to pry apart the top half from the bottom half. Wedge the plastic opening tool tool around the edge of the phone to dislocate the tabs.

Once the tabs are dislocated, pull the back of the phone apart from the front half.

Step 6

              Circuit Board

On the rear phone casing, locate the ribbon cable tab and connector next to the SIM card port.
Gently pull up on the tab to disconnect it from the connector.
Carefully remove the circuit board from the phone casing.

On the rear phone casing, locate the ribbon cable tab and connector next to the SIM card port.

Gently pull up on the tab to disconnect it from the connector.

Carefully remove the circuit board from the phone casing.

Step 7

              Keypad

Hold the front of the phone face down.
Using a T6 screwdriver bit, loosen the eight screws holding the keypad protector in place.
Loosen the keypad connector by lifting the rectangular plate up with one finger.

Hold the front of the phone face down.

Using a T6 screwdriver bit, loosen the eight screws holding the keypad protector in place.

Loosen the keypad connector by lifting the rectangular plate up with one finger.

Step 8

Use the plastic opening tool to loosen the keypad protector from the faceplate.
Once the protector is loosened, use the plastic opening tool to slide the keypad protector towards the screen while pulling on it with two fingers.
Remove the keypad protector and connector from the faceplate.

Use the plastic opening tool to loosen the keypad protector from the faceplate.

Once the protector is loosened, use the plastic opening tool to slide the keypad protector towards the screen while pulling on it with two fingers.

Remove the keypad protector and connector from the faceplate.

Step 9

Hold the phone with the keypad facing up and gently push on the keypad with one finger to dislodge it from phone.
Place the keypad to the side.

Hold the phone with the keypad facing up and gently push on the keypad with one finger to dislodge it from phone.

Place the keypad to the side.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      One other person completed this guide.

Author

                                      with 5 other contributors

                    John Miller

Member since: 10/22/2012

50 Reputation

                                      4 Guides authored                  



                       Badges:
                       7







                                                        +4 more badges

Team

                       Clemson, Team 15-4, Benson Fall 2012                        

                                                  Member of Clemson, Team 15-4, Benson Fall 2012 



                    CLEM-BENSON-F12S15G4                     


                                            4 Members                     


                                            20 Guides authored

Introduction#

What you need#

Team#

Introduction

What you need

Team